|
|
|
Who's Online
There currently are 5919 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
2061X Front Panel
2061X Rear Panel
ENGLISH
ENGLISH
1
2
3
4
5
6
7
8
1
2
3
4
5
1. POWER SWITCH
This is the On/Off switch for mains power to the amplifier. Note: Please ensure the amplifier is switched off and unplugged from the mains electricity supply whenever it is moved.
7. VOLUME CONTROL
This controls the volume of the Bass Channel. Turning it clockwise increases the volume level of the channel.
1. LOUDSPEAKER OUTPUTS
There are two parallel loudspeaker output jacks provided for connection to speaker extension cabinet(s). Please always ensure that the amplifier�s output impedance is set correctly (item 2). WARNING! Never use the head without a load attached! Always use a non-screened Marshall approved speaker lead when connecting an extension cabinet to these units.
3. H.T. FUSE
The correct value of H.T. fuse is specified on the rear panel of the amplifier. NEVER attempt to bypass the fuse or fit one of the incorrect value.
8. BASS CHANNEL INPUTS
These are the guitar inputs for the Bass Channel. The top input is �high sensitivity� and the bottom input is �low sensitivity�, the latter being 6dB lower in volume than the former with a darker sound. Always use a high-quality, screened guitar cable.
4. MAINS INPUT
Your amp is provided with a detachable mains (power) lead, which is connected here. The specific mains input voltage rating of your amplifier is shown on the back panel. Before connecting for the first time, please ensure that your amplifier is compatible with your electricity supply. If you have any doubt, please get advice from a qualified technician. Your Marshall dealer will help you in this respect.
2. INDICATOR
This 6.3 Volt incandescent filament indicator will light up when your amplifier is switched on. It will not be lit when the amplifier is switched off and/or is not receiving mains power.
Performance Note: Bridging or �jumping� the two channels
Because both Channels of the 2061X have the same number of gain stages (one) and are therefore in phase with each other, it is possible to bridge them together (a.k.a. �slaving�, �jumping�, �linking� or even �daisy-chaining�) and use them both at the same time, enabling you to expand upon the amps tonal possibilities by mixing the Lead and Bass channels together. The most common way of doing this is to plug your guitar into the top (high sensitivity) input of one of the two channels and then run a short �jumper� guitar cable (i.e. a screened cable) from that channel�s bottom (low sensitivity) input to one of the other channel�s two inputs. It is also possible to plug your guitar into the bottom (low sensitivity) input of one of the two channels and then run the �jumper� cable from its top (high sensitivity) input to one of the other channel�s two inputs. This less-common approach can also yield some interesting tonal variations.
2. OUTPUT IMPEDANCE SELECTOR
Matches the amplifier�s output to the load (speaker) impedance. As is the case with any Marshall all-valve amplifier it is imperative that: a) the amplifier is connected to a load whilst in operation and b) the impedance selected on the amplifier matches the total impedance of the extension speaker cabinets being used. WARNING! An extension speaker cabinet with an impedance of less than 4 Ohms, or two extension cabinets of 4 Ohms or less should NOT be used with this head. The amp should be completely powered down before the Output Impedance Selector is turned. Failure to comply with any of the points raised in this section will result in damage to the amplifier.
LEAD CHANNEL 3. TONE CONTROL
This adjusts the tonal character of the Lead Channel. Turning this control clockwise increases the amount of high frequencies (treble) in the sound.
5. MAINS FUSE
The correct value of mains fuse is specified on the rear panel of the amplifier. NEVER attempt to bypass the fuse or fit one of the incorrect value.
4. VOLUME CONTROL
This controls the volume of the Lead Channel. Turning it clockwise increases the volume level of the channel.
5. LEAD CHANNEL INPUTS
These are the guitar inputs for the Lead Channel. The top input is �high sensitivity� and the bottom input is �low sensitivity�, the latter being 6dB lower in volume than the former with a darker sound. Always use a high-quality, screened guitar lead.
BASS CHANNEL 6. TONE CONTROL
This adjusts the tonal character of the Bass Channel. Turning this control clockwise increases the amount of high frequencies (treble) in the sound.
Follow all instructions and heed all warnings KEEP THESE INSTRUCTIONS !
4
5
|
|
|
> |
|
