|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
;
Quick delivery, the document was usefull, although the copy was i little bit unclear in the details.
6.
Detector and AM Stereo Decoder (Cont.) During AM operation, transistors Q5 and Q6 conduct to apply the regulated 10 volts to pin 6 of U3. The AM audio outputs pin 7 (left) and pin 8 (right) are applied to the filter/Amp IC (U7).
C.
FM CIRCUIT
1.
FM Front End - The completely integrated FM front end, U4, performs the following functions AGC, RF amp, mixer, oscillator and IF. Increased quality and reliability are achieved by integrating the discrete components. The signal from the antenna is hard wired to pin 13 and the output on pin 6 is the intermediate frequency. Tuning voltage is applied to pin 10 to determine the resonant frequencies of the varactor diodes, capacitor and coil combinations, for the RF, mixer and oscillator stages. Search sensitivity is controlled by pin 4 and the AGC input is applied to pin 3. Pin 1 supplies the IF output to the synthesizer. During FM operation, switched supply voltage will be applied to pin 5 because of the conduction of Q9 and Q8. Audio Detection and Station Detector - The IF output out of the front end is applied to pin 2 of u5. The IF amplifier output has two outputs, one to the level detector for AGC output pin 6 and the other to a buffer amplifier. The buffered IF output on pin 16 is connected to pin 15 by R37. Pins 14 and 15 are the inputs to the peak detector which has two outputs, one for the AF amplifier and the other to the frequency change detector. The detected audio is amplified and outputting on pin 10. Operation of the frequency change detector is determined by R39, C48 and C49. Station detect sensitivity is determined by R36 and C47. The station detect output pin 7 turns on Q7 when a station is detected. An internal regulator regulates the Vcc voltage level. Stereo Decoder and Blend - The separation of the left and right audio is accomplished in the FM stereo decoder U6. The multiplexed audio signal goes in on pin 3 and is outputted as left and right audio pins 4 and 6. The frequency of the PLL 19 kHz pilot detector is set at pin 16. The internal Vco frequency can be measured at pin 11 with a sufficiently high impedance counter through a 56K resistor or greater. The IC also contains a stereo
2.
3.
l-20
|
|
|
> |
|