|
Who's Online
There currently are 5917 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
F. ADJUSTMENT PROCEDURE
ITEM Program Menu.
�Test Meter ﹡Test Point ﹫Pattern �Digital Voltmeter ﹡D510 Negative ﹫Crosshatch Pattern (31.5KHz,640x480)
Operation
Adjusting Value 15.5V ±0.2V
B+ Adjust A
1. Make the adjustment to the value shown at right by turning the VR501 on the main PCB.
High Voltage �Digital Voltmeter 1. Turn the power switch of the monitor OFF. Adjust �High Voltage 2. Connect high voltage probe to Anode Cap and Probe GND. B ﹡Anode Cap-GND 3. Turn the power switch of the monitor ON. ﹫Crosshatch Pattern (15 minutes) (31.5KHz,640x480) 4. Make the adjustment to the value shown at right by turning the VR601 on the main PCB.
26.0KV (17�,19�) 25.0KV ±0.1KV (15�)
Preset Adjust
﹫Crosshatch (31.5KHz,640x480)
1. Turn the power switch of the monitor OFF. 2. Hold encorder key,then turn the power switch of the monitor ON.(one key type) Hold MENU key,then turn the power switch of the monitor ON.(four key type) 3. Turn encorder/MENU key,make sure into preset picture,if not ,please return 1-2. 4. Please following the procedure of selection and adjusting an item using the OSD system as below steps for main function adjusent.
C
Contrast : MAX. Brightness MAX. H-Size : 260mm(15�) 310mm(17�) 360mm(19�) V-Size : 190mm(15�) One key model : 230mm(17�) Step 1 : Press and relese the OSD control knob to 270mm(19�) activate the OSD menu. H-Posi. : Step 2 : Turn the knob to highlight the desired option Center of OSD icon. V-Posi : Step 3 : Press and release the knob again to access the option. The color of the inner area of the OSD will changed from blue to green. Step 4 : To make your adjustment,turn the knob clockwise to increase or countclockwise to decrease the setting. Step 5 : Press and release the knob again to store the change.the color of the inner area will go back to blue.You can select EXIT icon and press the knob the exit the OSD menu. Center
11
|
|
|
> |
|