CAD E100
User Guide

to select the proper mode. From the factory, the two pins towards the left are shorted to enable the auto shut off circuit. To disable the circuit, pull off the jumper and replace it so that the two pins towards the right are shorted. The microphone can also be used with phantom power when it is in this mode, however you must remember to turn the microphone off when not in use or the batteries will be depleted.

A Special Note About Batteries

The high quality rechargeable batteries used in the Equitek E-100 are Nickel Metal Hydride type. They were selected to provide long life with virtually no maintenance and have a number of properties that make them superior to most commonly available rechargeable "9 volt" batteries: 1) Higher output voltage 2) Lower self discharge rate 3) High immunity to overcharging If the E-100 is operated with a 48 volt phantom power supply it is unlikely they will ever need to be recharged, even if the microphone is unused for months. If it should ever become necessary to replace the batteries or if you simply want a spare set, we suggest that you buy replacements from us. This is not because we are trying to sell batteries, but because we want you to continue to realize the maximum performance capability of your Equitek microphone. Contact the CAD sales department to purchase replacement or additional batteries.

User Techniques and Applications

The Equitek E-100 has a built in swivel that allows easy microphone positioning and mates to any microphone stand that has standard 5/8" X 27 threads. Loosen the large thumb screw on the back of the mic to change the mic position. The E-100 can be used in a broad number of applications, ranging from live reinforcement to the most critical studio situations. The E-100 is ideal for vocals and voice overs, yet it also excels at some of the most demanding instrumental projects. The E-100 is great for virtually all acoustic, wind, and amplified instruments. One of the most popular uses for the E-100 is in miking drum sets, especially kick drums. The E-100 has been proven to be outstanding in all of these applications and more. Its uncolored sonic characteristics allow you to decide how a instrument or vocal will sound in the mix. The supercardoid polar pattern is very useful in live applications where feedback control and tight miking are required. The E-100 is available in hand selected, electronically matched pairs for stereo recording applications. The model number is E-100MP. The microphones come in a hard shell carrying case and are matched for output level and frequency response. (See photo below.)

Specifications

Type: Side Address, Supercardioid Electret Condenser. Frequency Response: 10-18 kHz (See Back Cover). Polar Pattern: Supercardioid (See Back Cover). Impedance: Low (200 ohms nominal). Output Level At 1 kHz.: Power Level: -34 dB (0 dB = 1 mW per 10 microbars). Open Circuit Voltage: -55 dB (0 dB = 1 volt per microbar). 17.8 mV/Pascal. Dynamic Range: 132 dB. Equivalent Noise Level: 16 dB Equivalent SPL, A weighted. Maximum Output Level: With pad, .89 dBV. Without pad, 8.9 dBV. Maximum SPL: 148 dB SPL (With pad on). Total Harmonic Distortion: Less than 0.15%. Signal-To-Noise Ratio: 78 dB (At 94 dB SPL). Capsule Capacitance: 60 pF. Powering: Minimum Requirements are 48 - 52 Volts Phantom Power capable of delivering at least 8 mA. Connector: Three pin male XLR type. Finish: Durable black urethane. Brass plated front screen. Dimensions: 2.45" (62.2 mm) Wide., x 6" (153.4 mm) High x 2.175 (55.2 mm) Deep. Net Weight: 18 oz. (510 grams).

E-100MP Matched pair

Optional Accessories: EPF-15 ... P-pop filter mounted on 15" gooseneck with standard bracket 40-350 ..... 50 ft. broadcast quality extension cable ..terminated with professional 3 pin male/female connectors. 40-351 ..... 100 ft. broadcast quality extension cable. 40-352 ..... 25 ft. broadcast quality extension cable.