|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
;
The manual was exactly what I wanted and I found it nowhere else. Thanks!
;
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Top marks.
John Copeland
Glasgow
Scotland
;
I was so happy that the owner's manual was available. It is well written and helped me to use the radio/CD player/recorder without problems. Thanks for making it available.
Irene Lambert
400RB-IV Series
Front Panel Controls
Front Panel Controls
1-Balanced Direct Out: An electronically balanced output, that you can run to your P.A. system. 2-Ground/Lift: This switch disconnects the ground on the balanced, XLR output to eliminate hum and buzz when connnecting to equipment that is running on a different ground system. Pre/Post EQ Button: Selects the direct out signal before or after the EQ. 3-Input: A standard ¼� input jack to plug in active or passive basses using a shielded cord. 4- -14dB Pad: Input attenuator button. The button is generally left out, except in rare cases when the clip LED flashes. This switch should be pressed if the CLIP LED stays on continuously. It may be necessary to �pad� the input if you are using a bass with active electronics or very high output. Clip LED: LED lights yellow when the input stage is being over-driven. If -14dB PAD is pressed and clip LED still stays lit, turn down the volume on your bass. Tuning Mute Button: Set this switch to �On� when tuning up. No signal will be sent to the speakers, or the P.A. system. Mute LED: LED turns on when �Tuning Mute� is switched to the �ON� position. 5-Volume: Sets pre-amp gain after the input stage. It is used in conjunction with the input pad, to optimize the amplifier�s headroom. 6-Voicing Filters: 4/5 String Bass: Setting this button to the �ON� position, voices the pre-amp for basses with �B� tuning (5 string bass). Leaving it in the �Out� position will voice the amp like the 800RB, for a 4 string bass. Contour: Drops the mid-range frequencies while boosting lows & highs. Presence: Adds edge and definition to higher frequencies. Active Equalization: 7-Treble: Boost and cut at 7 kHz +14dB shelving type. Add or remove edge and definition. 8-High Mid: Boost and cut at 1 kHz +6dB/ -10dB, �Q Optimized,� band pass type. Works on lower string harmonics, and effects the punch of your sound. 9-Low Mid: Boost and cut at 250Hz +6dB/-10dB, �Q Optimized,� band pass type. Works on the main body of your sound. 10-Bass: Boost and cut at 60Hz +10dB, shelving type. Controls low end push. 11-Boost: A post EQ gain stage using GIVE technology which adds �growl� as it is turned up. 12-Master: Controls the output level of the amplifier. 13-Effects Loop: Send and return jacks provided for the insertion of effects after the EQ, but before the boost section. Some effect units have gain, turning the BOOST down, will compensate for this. 14-Tuner Output Output comes directly off the input stage and can be patched to a tuner with a shielded patch cord. This output is unaffected by the Tuning Mute Feature. 15-Power/Protect LED: The LED is red at turn-on for five seconds while the amp powers up. The LED turns blue when the amp is ready to play. Should the amp experience a fault (over heat, over current) the amp will mute and this LED will switch to red until the condition is corrected. This LED turns off when the power switch is turned off. 16-Power Switch: Turns the amplifier on or off. Should a problem occur during operation press this switch out first. This turns the amp off, but does not completely disconnect the power from the AC mains. The power LED should be off at this point.
10
|
|
|
> |
|
