|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
very helpful, the information in these manuels are very detailed
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.00 of store credit for Your review.
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.00 of store credit for Your review.
;
Good copy and great customer service! There was some confusion with my order and it was resolved promptly!
;
Having bought a pre-owned Sony FM stereo tuner through eBay, it came without any manuals. It soon became clear that to get the best from this excellent tuner I needed a decent manual because much of the operation was not intuitive to a newboy to hi fi like me. I managed to download the official Sony multi-lingual manual from Owner-Manuals.com with no problem at all - a really quick and easy service. I'm very glad I did because I found out all the operations of the tuner and was then able to not only set it up quickly but also to get much more from it that poke-and-hope trialling would ever achieve. In my book $4.99 very well spent.
Studio Monitor Model 4318
1: Introduction
Thank you for purchasing the JBL 3-Way Studio Monitor 4318. In order to better understand and correctly use this product, please thoroughly read this Owner's Manual before using the product.
2: Unpacking
The product should have been delivered complete in appearance and functionality. However, if you find any scratches or defects, please directly contact the store where you purchased the product. We recommend that you keep the original box and packing material after unpacking. Please note that if a product must be shipped for a repair service, JBL Incorporated will not be responsible for any damage incurred during shipping caused by insufficient packing.
3: Installation
Avoid placing the monitors near power amplifiers or radiators that generate large amounts of heat, or in very humid or dusty places, and any places exposed to direct sunlight. Also place them on a firm, solid floor. �Settings Start the setup using a recorded sound source that has a distinct virtual center image. Once the center point between the speakers is obtained by measuring equal distances from the left and right speakers, adjust the distance between the listening position and the speakers, as well as the distance between right and left speakers, so that a precise center image is obtained. These monitors are designed to reproduce the most accurate stereo sound stage when the interior angle between the lines connecting from each speaker to the listener is between 40 to 60 degrees. Additionally, it is ideal that a distance of approximately 50 cm or more is maintained from the left and right walls. The center of the speaker's sound image is in the vicinity of the HF (high-frequency) unit. Set the speakers so that the HF unit is aligned at ear-level. In addition, to avoid acoustical interference with the floor surface, it is recommended that you set a sturdy base (cube or block shaped) with a thickness of 5 � 20 cm under the speakers.
4: Connection *Caution
When connecting the speakers to the amplifier, always do so after turning off the power. Connecting the speakers while the power is on may damage the amplifier or the speakers. The positive terminals of the speaker have a red ring, and the negative terminals have a black ring. Be sure to connect without mistaking the polarity. The speakers are designed so that when a positive signal is applied to the positive terminal, the woofer moves in the forward direction (positive phase operation). In order to safely and securely connect to the terminals, we recommend that you use the Y terminals or banana plugs on the cable ends.
5. Attenuator Adjustment
Independent, continuous variable attenuators are used for each unit to adjust the MF (mid-frequencies) and HF (highfrequencies) levels to the speaker's woofer level. Make adjustments appropriate to the reverb in the actual room, and to your liking. In general, for most speakers, it takes about 1 � 2 months after initial use until the unit's vibration system yields optimum performance. As the level balance is expected to initially change with use, we recommend that you readjust the level accordingly.
|
|
|
> |
|
