|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
;
The manual was very helpfull, it answerdes all my questions, and i was surprized to find the original manual on this site! Big thumbs uP:)
 ;
helpful manual.good service.Quick response.will use again
;
Speedy confirmation to my order , with elaborate instructions .
Item Email , received immediately as desired by me.
A Pleasant & Satisfying Transaction.
;
I was searching for this manual at last i got it from this web
ENCORE DUET RECEIVER
1. Rackmounting the Receiver There are 2 options available for rackmounting the Encore DUET receiver: singly or side-by-side with another Encore Series receiver. a. Single mounting: Remove the receiver SIDE MOUNT CLIP (1) from each side of the receiver (as shown) and slide in the optional ERM-12 RACK EARS (9). b. Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from both Encore receivers, join the two receivers with the EJC-2 JOINING CLIP (10) and attach the ERM-22 RACK EARS (12) as shown. (Note: Do not mount the receiver in a rack directly above an ampli�er or other source of high heat � this could degrade the performance of the Encore DUET. Always ensure adequateair�ow and heat dissipation in any rack con�guration.)
43
38
44 36
37
41 45
2. Powering the Receiver Plug the 12V AC/DC ADAPTER (15) provided into the DC INPUT JACK (11) on the back of the receiver. Then plug the power supply into an AC outlet. (Note: Any 12V DC source with 400mA capability can also be used.) Press the POWER SWITCH (8) once to turn on the receiver. The POWER ON LED (7) will now light and the receiver is operational. 3. Antennas The Encore DUET receiver is supplied with TELESCOPIC ANTENNAS (16), one each for Channel A and Channel B. These should be extended fully to obtain maximum range. Optimal antenna position is 45 degrees from the receiver (at 90 degrees from each other). For maximum range, it is always best to maintain a line of sight (no obstructions) between the receiver antennas and the transmitter at all times whenever possible. 4. Mute (Squelch) Adjustment In normal operation, the MUTE CONTROLS (2) for each channel (A & B) should be set fully counterclockwise to the factory preset minimum RF level. However, in areas of high RF activity, the mutes (or squelches, as they are sometimes called) may need to be adjusted to compensate for the adverse conditions in a particular location. If, with the transmitter off, one or more LEDs of the receiver's 5 LED RF LEVEL DISPLAYS (4) for that channel transmitter �icker or stay on, the squelch control for that channel should be turned clockwise until the LEDs extinguish. When the squelch is properly adjusted, the RF LEVEL LED displays will only light when that channel transmitter is turned on. Turning the squelch control too far clockwise will reduce the range, but yield a quieter mute (squelch) function. When the 5 LED RF LEVEL display extinguishes, the transmitter for that channel is out of range for that given location, and the user should move closer to the receiver to re-establish the radio link.
39 40 42
36 37 38
XLR Connector � Connects microphone to the transmitter module for signal input Locking Ring � Locks microphone to the transmitter Optional Pouch � For lavalier bodypack operation (with beltclip and strap ring for securing)
39 40 41
Gain Control Switch � Adjusts the input sensitivity (LO or HI) Low Battery LED � Single �ash (power on), lit steady (low battery) Power Switch � Turns the power ON/STANDBY/OFF. In standby position, the power is on and the audio is off.
42 43 44 45
Phantom Power ON/OFF Switch � Turns the phantom power ON/OFF Battery Compartment Release Button � Press to release XLR connector 9V Alkaline Battery
16
5
|
|
|
> |
|
