|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The Service Manual for Sansui AU-9500 was very helpfull, in complete and in good printable condition.
Thanks.
;
Dear Sir,
Document is original service document of sharp. I had a problem with the door contacts. Fuses where blown. With the manual in a few minuts is was clear what the problem was.
Manual was of great help.
With kind regards,
Martie Verhoeven
The Netherlands.
 ;
The scan is clear and well readable with very few weaker spots, usually on black background with white letters, but with enough zoom those spots can be read.
Printout is clear, the manual is complete and has all pages scanned.
I would give 5 stars, except that it is not in color, and the schematic and PCB pages are scanned on multiple pages. The document is locked (except printing) so the pages can not be extracted to compose them together for printing on the large plotter
It is worth the price tag.
;
let's say first that i do not need to have a credit for my opinion, i am a retired sparkie and i voluteerd to fix an electronic device for a local "Youthgroup",as no diagram was present i checked the "net" and gambled on this site and paying some fee via PayPall, i was gladly surprised that the manual arrived as was stated, GOOD SHOW, and best wishes, John
;
I had been looking for a Manual for my CS2150 for quite a while -- in fact I had just about given up. I saw this site and decided to download the Manual. When I Received it by Email I was really pleased with what I got, with the result that My Kenwood 'Scope is now 100% repaired and working well. As an AV Serviceman, you need a good 'scope, and thanks to this site, and the Service Manual, I have been able to repair it. The Manual was a copy of the Factory Original and the copy was very clear, especially in the area of the Circuit Schematics, where You really need to be sure of what You are looking at.
ADJUSTMENT
Y Safety Precautions
1. It is safe to adjust after using insulating transformer between the power supply line and chassis input to prevent the risk of electric shock and protect the instrument. Never disconnect leads while the TV receiver is on. Don't short any portion of circuits while power is on. The adjustment must be done by the correct appliances. But this is changeable in view of productivity. Unless otherwise noted, set the line voltage to 230Vac!10%, 50Hz. TUNER AGC Voltage Default AGC Data 6700VPV002A(LG C&D) 2.5 ! 0.1V 24 6700VPV002B(LG C&D) 3.0 ! 0.1V 24
2. 3. 4. 5.
: Screen Voltage Adjustment
Test Point Adjust : RK (Red Cathode of CPT Board) : Screen Control of FBT
Y Test Equipment required
1. 2. 3. 4. 5. RF signal generator (with pattern generator) DC Power Supply Multimeter (volt meter) Oscilloscope Color analyzer
1) Input the Color Bar Pattern into Antenna jack. 2) Select CutOff of SVC-3 mode. 3) Turn the screen control clockwise until the Horizontal line is visible and turn it counterclockwise until the Horizontal line is faintly visible.
: RF AGC (Automatic Gain Control) Adjustment
Test Point Adjust : AGC TP (J17) : Remote Control NOTE: This adjustment should be performed after warming up for 10 minutes. The RF AGC was aligned at the time of manufacture for optimum performance over a wide range conditions. Readjustment of RF AGC should not be necessary unless unusual local conditions exist, such as ; 1) Channel interference in a CATV system. 2) Picture bending and/or color beats, which are unusually due to excessive RF signal input when the receiver is too close to a transmitting tower or when the receiver is connected to an antenna distribution system where the RF signal has been amplified. In this case, the input signal should be attenuated (with pad or filter) to a satisfactory level. 3) Picture noise caused by "broadcast noise" or weak signal. If the broadcast is "clean" and the RF signal is at least 1mV (60dBu), the picture will be noise free in any area. Adjusting RF AGC to one end of rotation will usually cause a relatively poor signal to noise ratio; Adjusting to the other end of rotation will usually cause a degradation of over load capabilities resulting in color beats or adjacent channel interference. Test Point Adjust : Observing Display : Focus control of FBT
: Focus Adjustment
1) Input the Color Bar Pattern into Antenna jack. 2) Adjust the Focus control of FBT for best overall focus.
: VCO Adjustment
1) Input Digital Pattern into Antenna jack. 2) Select A-PIF of SVC-4 mode. 3) Press VOLF/G button and A-PIF will be changed 0 to 1 while the number of PIF-C is rolling. 4) When PIF-C stops rolling, A-PIF will be changed 1 to 0 and VCO adjustment is finished. Caution : Do not press the Volume button again in A-PIF mode after adjustment is finished. 1. To get into SVC mode 1) Press OK buttons on both TV set and Remote Control at the same time. 2) Press Yellow button to select OPTION-1, OPTION-2, OPTION-3 or OPTION-4. 3) Press PR E/D button to select an adjustment. 4) Press VOL F/G button to change the data. 2. To memorize the adjusted data into EEPROM Press OK button. 3. To get out from SVC mode Press TV/AV or Power button.
Adjustment
1. Connect RF signal (65dB!0.5dB) and turn on the TV. 2. Press OK buttons on TV set and Remote Controller at the same time to get into SVC mode. 3. Press Channel UP/DOWN button on the Remote Controller several times to find AGC. 4. Press Volume UP/DOWN button until the AGC Voltage is the same as the Table below. 5. Press OK(Y) button to memorize the data.
-1-
|
|
|
> |
|
