|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
Clarion Co., Ltd.
50 Kamitoda, Toda-shi, Saitama 335-8511 Japan Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703
Published by Service Dept. 298-6023-01 Jan.2005 Printed in Japan
Service Manual
NISSAN Automobile Genuine Satellite Tuner
Model
EN-1187E
After Serial No.0027925 (Genuine No.28051 CR900)
ORIGINAL SERVICE MANUAL
After Serial No.0027925 of this model, please confirm that and correspond to the original manual. This additional service manual is designed to be used together with Original model. Original model EN-1187E-A Manual No. 298-6023-00
DIFFERENCE FROM ORIGINAL MODEL
1. Change of the System Controller IC 2. Additional of the deatails of IC explanation 3. Additional of the Label(Software version code) 4. Change of the components
4. 4-1. 4-2. 4-3. 4-4. 5. 5-1. 5-2. 5-3. 6. 6-1.
Parts bag Mounting bracket Tap screw D-sems-hex-bolt Hex flange bolt Parts bag Insulok tie Corrugate tube Bonding wire Parts bag Black tape
----------300-7362-03 704-5010-81 734-4008-31 782-6016-00 ----------335-3847-00 825-1179-01 840-0539-00 ----------348-0334-00
2 4 4 1 4 1 1 2
To engineers in charge of repair or inspection of our products.
Before repair or inspection, make sure to follow the instructions so that customers and Engineers in charge of repair or inspection can avoid suffering any risk or injury.
1. Use specified parts. The system uses parts with special safety features against fire and voltage. Use only parts with equivalent characteristics when replacing them. The use of unspecified parts shall be regarded as remodeling for which we shall not be liable. The onus of product liability (PL) shall not be our responsibility in cases where an accident or failure is as a result of unspecified parts being used.
NOTES
* We cannot supply PWB with component parts in principle. When a circuit on PWB has failure, please repair it by component parts base. Parts which are not mentioned in service manual are not supplied. Specifications and design are subject to change without notice for further improvement.
*
COMPONENTS
EN-1187E-A
1. 2. 3. 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. Main unit Clamp Parts bag Edge protector Seal rubber Urethane sheet Spacer Magic tape Magic tape Protect seal ----------321-1026-00 ----------345-5247-00 345-5252-00 345-7010-00 345-8276-00 348-0105-02 348-0106-02 348-0333-00 1 4 1 2 14 1 2 2 4
2. Place the parts and wiring back in their original positions after replacement or re-wiring. For proper circuit construction, use of insulation tubes, bonding,gaps to PWB, etc, is involved. The wiring connection and routing to the PWB are specially planned using clamps to keep away from heated and high voltage parts. Ensure that they are placed back in their original positions after repair or inspection. If extended damage is caused due to negligence during repair, the legal responsibility shall be with the repairing company.
-1-
EN-1187E
|
|
|
> |
|
