|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
AV-28BT8ENS / AV-28BT8ENB / AV-28BT80EN AV-28BT8EPS / AV-28BT8EPB / AV-28BT80EP AV-28BT8EES / AV-28BT8EEB/ AV-28BS88EN
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power c ord. 2. Remove the 8 screws marked A as shown in the Fig. 1. 3. Remove the 4 screws marked B around the AV TERMINAL BOARD. 4. Withdraw the rear cover toward you.
CHECKING THE PW BOARD
To check the back side of the PW Board. 1) Pull out the PW Board. (Refer to REMOVING THE MAIN PWB). 2) Erect the PW Board vertic ally so that you c an easily check the back side of the PW Board. [CAUTION] " When erecting the PW Board, be c areful so that there will be no contacting with other PW Board. " Before turning on power, make sure that the wire connector is properly connec ted. " When conducting a check with power supplied, be sure to c onfirm that the CRT EARTH WIRE (BRAIDED ASS�Y) is connected to the CRT SOCKET PW board.
REMOVING THE AV TERMINAL BOARD
" Removing the rear cover. 1. Remove the 2 screws marked C fastened the AV TERMINAL BOARD. 2. Remove the AV TERMINAL BOARD.
REMOVING THE MAIN PWB
" Removing the rear cover. " Removing the AV TERMINAL BOARD. 1. Remove the 3 screws marked D as shown in the Fig.1. 2. Slightly raise the both sides of the chassis by hand and withdraw the MAIN PWB backward. (If necess ary, take off the wire clamp, connectors etc.)
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new c able tie.
REMOVING THE SPEAKER
" Removing the rear cover. 1. Remove the 4 screws marked E, and remove speaker as s hown in Fig. 1. 2. Remove the speaker.
REMOVING THE FRONT AV & HEADPHONE PWB
" Removing the rear cover. " Removing the MAIN PWB. 1. Remove the 2 screws marked F. 2. Remove the FRONT AV & HEADPHONE PWB.
REMOVING THE FRONT CONTROL PWB
" After removing the rear cover . 1. Remove the MAIN PWB ASS�Y. 2. Remove the 5 screws marked G, and remove the FRONT CONTROL PWB.
6
No.52057
|
|
|
> |
|
