|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly what was needed to assess the product - excellent value and great service
 ;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
HOW TO LOAD SOFTWARE FOR MPEG P.W.BOARD
a. Push the power button to ON. b. Push the OPEN/CLOSE button to open the tray. c. Place the CD-R disc into the tray for updating. Then push the OPEN/CLOSE button to close the tray. (Do not press PLAY key.) If tray is done in close excluding OPEN/CLOSE key. It does not become update mode. d. The under mentioned display appears to the screen READING doing and about 6 seconds later. Display on "FL" UPDATE DSC Display on screen. It is not possible to discontinue on the way when Update begins. Detect firm update disc to start updating : press PLAY key. to quit : press OPEN key. f. After 40 seconds, the picture will become off. Then STANDBY LED light. Update complete. POWER key press and OPEN/ CLOSE key press and take out the CD-R. g. Execute initializing. h. Using remocon, press on SET UP , Parental , 460076 , ENTER and SET UP. i. Initializing of SET UP complete.
Version US UK,XE CA,SS SS AU,SS SS CD-R part code 0PRADD9606B1EE 0PRADD9606A29D 0PRADD9606A1EF 0PRADD9606A3ED 0PRADD9606A4ED 0PRADD9606A2EC Region No. 1 2 1 3 4 2 Description ENGLISH 9 LANG. English English English English
e. Press PLAY key then updating. Display on "FL" UPDATING Display on screen. Updating firmware -- Please wait Your player will restart automatically when complete.
Cancel is good at Update by pushing OPEN/CLOSE. After disk is inserted, keys other than OPEN/CLOSE key are disregarded.
Attention
1. Main power should not be cut off until the "STANDBY LED" lights up. 2. When the main power is cut off during installing, follow the procedure as below. A. When the main power is cut off before or after appearing the letters on the screen as mentioned at procedure #c, a. Plug out the power cord and plug it in again. b. Confirm that the "STANDBY LED" lights up. c. Push "OPEN/CLOSE" key. d. Carry out the rewriting procedure from procedure #b. B. When the main power is cut off within 9 seconds before completing the procedure #d, a. Plug out the power cord and plug it in again. b. Confirm that the "STANDBY LED" lights up. c. Push "OPEN/CLOSE" key. d. Carry out the rewriting procedure from procedure #b. In case the "STANDBY LED" does not light up even if the power cord is plugged out and in several times, the "FLUSH MEMORY" might get damaged. Please change the "FLUSH MEMORY" or the "MPEG PWB" and carry out the rewriting procedure from restart. - 38 3. When "READING" or "0:00" appears on the FL, a. Plug out the power cord and plug it in again. b. Confirm that the "STANDBY LED" lights up. c. Push "OPEN/CLOSE" key. e. Carry out the rewriting procedure from inspection #b.
|
|
|
> |
|
