|
Who's Online
There currently are 826 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
 |
|
There are currently no product reviews.
 ;
The manual was very helpfull, it answerdes all my questions, and i was surprized to find the original manual on this site! Big thumbs uP:)
 ;
helpful manual.good service.Quick response.will use again
 ;
Speedy confirmation to my order , with elaborate instructions .
Item Email , received immediately as desired by me.
A Pleasant & Satisfying Transaction.
 ;
I was searching for this manual at last i got it from this web
 ;
What can i say but i would have been lost without your support.
Thank You!
Recording With The Timer (Continued)
L To confirm the program content, press the CONFIRM button on the Remote Control.
REC TIMER PROGRAM MODE 1 DAILY 2 MON-FRI 3 15(SAT) 4 5 COMPLETE SELECT PREVIOUS CH START STOP 82 4 : 3 0PM 6: 0 0 PM SP 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP 5 6 1 1 : 0 0AM 1 : 2 0 PM SP NEXT CHANGE DELETE
10:20AM OCT.15(FRI) +/â : SET SET RETURN : QUIT MENU
L To add to the program content: (1) Press the CONFIRM button on the Remote Control. (2) Press the + or â button to select âNEXTâ, then press the SET button. (3) To add a program, follow the steps (3) through (10) of âSetting The Program Timerâ.
REC TIMER PROGRAM MODE 1 DAILY 2 MON-FRI 3 15(SAT) 4 5 COMPLETE CH START STOP 82 4 : 3 0PM 6: 0 0 PM SP 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP 5 6 1 1 : 0 0AM 1 : 2 0 PM SP NEXT CHANGE DELETE
L Notes on the Timer Recording ⢠To correct any erroneous data entry made during program timer setting work: (1) Press the RETURN button on the Remote Control to return to the item you wish to change. (2) Press the + or â button on the Remote Control to reset the data. (3) To advance operation, press the SET button. ⢠If the video cassette runs out of tape before recording all the programs, the VCR will stop, eject the cassette and shut off automatically. ⢠If you keep disconnected the power cord, the program timer will be cancelled. ⢠If âcompleteâ is selected to enter the TIMER Standby mode when there is no cassette inserted, the PROGRAM TIMER indicator flashes for 3 seconds and the message âNO TAPEâ appears indicating that timer recording is not possible. ⢠If âcompleteâ is selected to enter the TIMER Standby mode while a cassette with the erasure protection tab removed is inserted, the PROGRAM TIMER indicator flashes and the cassette is ejected. ⢠To stop timer recording, press the STOP button. ⢠If no buttons are pressed within 3 minutes while setting a program, the set automatically returns to the normal viewing mode. ⢠A program cannot be set unless all the recording input data is set. ⢠During program timer setting (with the Program Timer indicator ON), the video set remains inoperative. To use the video set, press the TIMER ON/OFF button on the Remote Control to turn off the Program Timer indicator. After use, load the cassette tape into the video set, press the TIMER ON/OFF button and check that the Program Timer indicator lights up. ⢠Be certain that the correct TV signal mode (AIR/CABLE) is selected before you enter the Timer Standby mode. Otherwise, the VCR may not record the desired TV channel. ⢠If two Pre-Recording Timers overlap, the End Recording Time of the PROGRAM TIMER 1 will have priority over the Start Recording Time of the PROGRAM TIMER 2. Example: Pre-Recording Timerâs Interval
PROGRAM TIMER 1 PROGRAM TIMER 2
Start Recording
SELECT PREVIOUS
10:20AM OCT.15(FRI) +/â : SET SET RETURN : QUIT MENU
L To change the program content: (1) Press the CONFIRM button on the Remote Control. (2) Press the + or â button to select âCHANGEâ, then press the SET button. (3) Press the + or â button to select the program you wish to correct, then press the SET button. To reset the program, follow the steps (3) through (10) of âSetting The Program Timerâ.
REC TIMER PROGRAM MODE 1 DAILY 2 MON-FRI 3 15(SAT) 4 5 CH START STOP 82 4 : 3 0PM 6: 0 0 PM SP 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP 5 6 1 1 : 0 0AM 1 : 2 0 PM SP
COMPLETE NEXT CHANGE DELETE SELECT PROGRAM TO CHANGE 10:20AM OCT.15(FRI) SELECT +/â : SET SET PREVIOUS RETURN : QUIT MENU
L To delete the program content: (1) Press the CONFIRM button on the Remote Control. (2) Press the + or â button to select âDELETEâ, then press the SET button. (3) Press the + or â button to select the program you wish to delete, then press the SET button. (4) Press the CONFIRM button to return to the normal screen.
REC TIMER PROGRAM MODE 1 DAILY 2 MON-FRI 3 15(SAT) 4 5 CH START STOP 82 4 : 3 0PM 6: 0 0 PM SP 1 2 3 1 0 : 0 0AM 1 1 : 3 0 AM EP 5 6 1 1 : 0 0AM 1 : 2 0 PM SP
COMPLETE NEXT CHANGE DELETE SELECT PROGRAM TO DELETE 10:20AM OCT.15(FRI) SELECT +/â : SET SET PREVIOUS RETURN : QUIT MENU
7:00
Start End Recording Recording
8:00
8:30
End Recording
10:00
Note: ⢠During the Program Timer Setting (with the Program Timer indicator ON), it is impossible to change or delete the program content. To perform these operations, press the TIMER ON/OFF button on the Remote Control and turn off the Program Timer indicator.
Actual Recording Timerâs Interval
End Recording
PROGRAM TIMER 1 PROGRAM TIMER 2
Start Recording
7:00
Start Recording
8:30
End Recording
10:00
25
22-25 13VT-R100/150[E].pm65e
25
12/4/01, 2:26 PM
|
|
 |
> |
|