|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Easy to order the manual. Good quality and fast delivery.
;
The Service Manual for Sansui AU-9500 was very helpfull, in complete and in good printable condition.
Thanks.
;
Dear Sir,
Document is original service document of sharp. I had a problem with the door contacts. Fuses where blown. With the manual in a few minuts is was clear what the problem was.
Manual was of great help.
With kind regards,
Martie Verhoeven
The Netherlands.
 ;
The scan is clear and well readable with very few weaker spots, usually on black background with white letters, but with enough zoom those spots can be read.
Printout is clear, the manual is complete and has all pages scanned.
I would give 5 stars, except that it is not in color, and the schematic and PCB pages are scanned on multiple pages. The document is locked (except printing) so the pages can not be extracted to compose them together for printing on the large plotter
It is worth the price tag.
;
let's say first that i do not need to have a credit for my opinion, i am a retired sparkie and i voluteerd to fix an electronic device for a local "Youthgroup",as no diagram was present i checked the "net" and gambled on this site and paying some fee via PayPall, i was gladly surprised that the manual arrived as was stated, GOOD SHOW, and best wishes, John
A keypad connector (S507) is provided which utilizes the integrated low bandwidth ADC in gm2221 for scanning 5-6 keys (menu,V+,V-,P+,P- keys standard- source key optional) on the keypad. The keypad allows access to the OSD without using the remote IR controller. The L5-A board also has In System Programming (ISP) capability for the external flash ROM using DDC2Bi. This can be done using the D-Sub 15 (PC) connector on the board. ISP can also be performed using G-probe through the RS232 interface. One channel of the dual channel FET power switch (U602) is used to control the power sequencing to the LCD panel. Depending on the type of the panel, the input voltage to this FET device can be chosen as shown below: For +3.3V panels For +5V panels For +12V panels J601 is soldered on the main-board J600 is soldered on the main-board J603 is soldered on the main-board
An LM2576, a step-down regulator IC (U600), is used to generate the main +5V_STBY voltage on the board. This IC can deliver up-to 3 Ampers of 5Volts. There is no stand-by control for this regulator, which means this IC is always on, as soon as power is supplied to the board. U603(+3.3V_STBY) and U605 (+1.8V_STBY) linear regulators are used to supply the voltage necessary for the GM2221 IC and some peripherals. These voltages are also available in stand-by mode to power the microprocessor inside gm2221, LED, IR receiver IC and EEPROM. These devices are necessary to wake up the board from stand-by state. Second channel of the dual channel FET power switch (U602) is used to control cut some voltages in stand-by mode. These voltages are +5V, +3.3V and +2.5V. These voltages are used by the video processor (VPC 3230D), audio processor (MSP 34x0G), teletext processor (SDA5550), tuner and some peripheral IC�s and circuitry. In order to limit the stand-by power consumption, these voltages are not available in stand-by mode. Also the audio amplifier (TDA1517) is also in its stand-by mode using its dedicated stand-by pin. The board employs MSP3410G, a multi-system audio processor solution from Micronas. The system supports 4 audio input ports, one of which is not used on the L5-A board. Audio output is provided with speaker and headphone jacks (S409, S401) provided on the board. The sound IF signal from the tuner is connected to the audio processor directly.
|
|
|
> |
|
