|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
 ;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
ELECTRICAL ADJUSTMENTS
2-9: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3)
TV "A" Fig. 2-1 00 OSD A 2-10: VIF VCO 120% 1. Place the set with Aging Test for more than 10 minutes. 2. Receive an 80dB monoscope pattern. 3. Connect the digital voltmeter between the pin 5 of CP601 and the GND. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "VIF VCO". 5. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.5V. 2-11: SUB CONTRAST MANUAL 1. Receive a 70dB the color bar pattern. (RF Input) 2. Activate the adjustment mode display of Fig. 1-1 press the channel button (14) on the remote control to select "CONTRAST". 3. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "100". 4. Receive a 70db the color bar pattern. (Audio Video Input) 5. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~3. 2-12: BRIGHTNESS 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "BRIGHTNESS". 2. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes "136". 3. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~2. 4. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~2. 15 B Fig. 2-3
0%
100% Fig. 2-2 2-6: HORIZONTAL PHASE 1. Receive the center cross signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (05) on the remote control to select "H PHASE". 3. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-7: VERTICAL SIZE NOTE: Adjust after performing adjustments in section 2-6. 1. Receive the crosshatch signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V SIZE". 3. Press the VOL. UP/DOWN button on the remote control until the rectangle on the center of the screen becomes square. 4. Receive a broadcast and check if the picture is normal. 2-8: VERTICAL SHIFT NOTE: Adjust after performing adjustments in section 2-7. 1. Receive the crosshatch signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V SHIFT". 3. Press the VOL. UP/DOWN button on the remote control until the horizontal line becomes fit to the notch of the shadow mask.
|
|
|
> |
|
