|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
75
- Cable TV
Connect the cable TV signal to the CABLE/ ANTENNA 75 jack at the bottom of the TV. See page 12 for details on using Autoprogram to store channels in the TV�s memory. Note: This connection will supply stereo sound to the TV if the station you are viewing broadcasts stereo sound.
ANTENNA
- Cable box with RF IN/OUT
� Connect the incoming cable TV signal to the cable IN jack on the back of the cable box. � Connect a coaxial cable (not supplied) from the TO TV jack on the back of the cable box to the CABLE/ ANTENNA 75 jack at the bottom of the TV. Note: Your cable box may have a different label for the TO TV jack. Commonly used labels include OUTPUT or OUT. � Set the OUTPUT CH switch on the cable box to CH 3 or 4 (whichever is correct for your cable box). Next, tune the TV to the corresponding channel. Once tuned, change channels using the cable box, not the TV. Note: This connection will not supply stereo sound to the TV. The reason is that the RF output on a cable box - labeled TO TV, OUT or OUTPUT for example - will not send a stereo signal to the tuner (VHF/UHF) input on a TV.
CABLE
HDMI 1
H DM I 2
CABLE OR ANTENNA
IN
OUTPUT /OUT (TO TV)
75
2
3
Cable box
SIDE AV
- Cable box with A/V outputs
VIDEO IN
ANTENNA
AUDIO
L R
VGA
L
VIDEO IN
R
AUDIO
� Connect the incoming cable TV signal to a signal splitter (not supplied). The signal splitter enables you to avoid having to use the TO TV jack on the back of the cable box. This jack will not supply stereo sound to the TV. Note: Your cable box may have a different label for the TO TV jack. Commonly used labels include OUTPUT or OUT. � Connect a coaxial cable (not supplied) to a connector on the signal splitter and to the CABLE/ANTENNA 75 jack on the TV. � Connect another coaxial cable (not supplied) to a connector on the signal splitter and to the cable IN jack on the back of the cable box. � Connect A/V cables (not supplied) to the VIDEO IN and AUDIO L and R outputs on the back of the cable box and to the AV2 or Side AV video (labeled VIDEO IN) and AUDIO (labeled L and R) jacks on the back of the TV. � To view programs from your cable box, �rst press the SOURCE button on the remote control. � Press the cursor down or up buttons until the AV2 or Side AV signal source is selected. � Press the OK button to con�rm your selection. The AV2 or Side AV input source becomes current for the viewing of cable TV programs through your cable box. Note: If your cable box audio/video outputs do not supply video and stereo audio to the TV, you will need to make the connection shown above in �Cable box with RF IN/OUT.
CABLE
PC IN
S-VIDEO
S-VIDEO
1
CABLE OR ANTENNA
75
2
SPLITTER
4
AV2: L+R+CVBS
3
IN OUT
Cable box
Watching cable TV programs that don�t require the use of a cable box.
Since you�ve connected the cable TV signal directly to the TV�s tuner, you can also watch unscrambled programs by simply tuning to the desired channel; however, you must �rst use Auto program to store available channels in the TV�s memory. (p. 12) Note: This connection will supply stereo sound to the TV if the station you are viewing broadcasts stereo sound.
6
|
|
|
> |
|
