|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A great copy of the manual, and the only one I could find anywhere on the net! The circuit diagrams are easily readable, all component values marked and easy to see. A highly appreciated download!
 ;
Great Manual. This manual is available no where else. It was exactly what I was looking for.
;
The TEAC A-1500's Service Manual was instrumental in reviving this classic reel-to-reel. Not only does it have the schematics, exploded parts diagram and parts list, it also provided mechanical adjustment information that approximate factory default settings.
;
This service manual was determinant to enable to fix my Alpine Amplifier. I am pleased with my purchase. For a 5 star rating I would like to see a higher resolution scan of the printed circuit board lay-out because the gray scale grafics was dificult to see. Also some schematic diagrams were scanned at a slight angle. Never the less, it had all information I needed to troubleshoot and service my equipment.
;
Complete manual, the good quality of reproduction allows enlarged print-out of the schematic diagram in the size it probably had in the original print edition and which is necessary for practical use.
ADJUSTMENT PRECAUTIONS: Make sure TV set is in "Normal Condition" before switch to Service Mode for adjustment.
PIF PURITY ADJUSTMENT
No. point Adjusting procedure/conditions Waveform and others
Tuner IFT Get tuner ready to receive CH. E 9 1 PURITY ADJ. 1. Receive GREEN-ONLY signal. Adjust the
( PRESET ) signal,but with no signal input. beam current to about 700 µA.
Adjust PLL data. 2. Degauss CRT enough with the degausing coil.
Oscilloscope IF OUT 75ohm 100k
2. Connect sweep generator�s output cable to 10k 1n60 1000p 3. Maintain purity magnet at the zero magnetic
a b
tuner antenna. ( RF SWEEP ) field and keep the static convergence roughly
3. Adjust the sweep generator�s to 80dBuV. adjusted. Connect response lead ( use LOW IMPED4. Observe the points a, b as shown in Fig. 4-1
ANCE probe with wave detector ; see Fig.1 ) through microscope. Adjust landing to the the tuner�s IF output terminal. ( This terminal Fig.1 rank A requirements. must have probe alone connected ). 5. Orient the raster rotation to 0 eastward. E-9 CH
Fig. 4-1
5. Set RF AGC to 0 6 V no saturation with 6. Tighten up the deflection coil screws.
P C
-1.5+/-0.8dB
the waveform. » Tightening torque: 108 20 N (11 ± 2 kgf) shown in Fig. 2. rank requirements. If not, stick the magnet sheet A
6. Adjust tuner IF coil to obtain waveform as 7. Make sure CRT corners landing meet the A
to correct it. longer with a beam current over 700 µA.
A = B 2 RF-AGC 1. Receive "PAL COLOUR BAR" signal. Note: For the 50 ohm signal
Be sure to keep the tuner cover in position Fig.2 Note: This adjustment must be done after
during this adjustment. warming up the unit for 30 minutes or B
* For the following colours press R/C RGB key to
TAKE OVER » Signal Strength: 57 ± 1 dBµV (75 ohm open) strength gauge, when not change. POINT AD2. Connect the oscilloscope to TP201 (Tuner AGC u s g 0 / 7 5 i m p d a n c e 4-3 Fig. 4-2 JUSTMENT Terminal) as shown in Fig. 3. adapter, signal strength is (I C BUS (on52±1dBµV(75 rightohm ofopen), theinCRT)2 open). + TP201
Rank "A"
Oscilloscope CONTROL) stead of 57±1dBµV (75 ohm Blue-only Red-only
Green-only
7
7-1 7-2
0.1V Precaution: The loss of using
� impedance adapter
+
Bias box TV Set Signal-colour A screen cleared
�
B A = B
» Bias box: About 4.5 V
Fig. 3
3. Call "AGC" mode in service mode. Adjust the
4. Change the antenna input signal to 63~67dBµV, (on left of the CRT)
"AGC" bus data to obtain the Tuner output pin drop 0.1V below maximum voltage. Rank "A"
and make sure there is no noise.
5. Turn up the input signal 90~95 dBµV to be sure * Press R/C RGB key for 1 sec-
that there is no cross modulation beat. ond in NORMAL MODE, the
colour will change to RGB mono colour mode. The TEXT "R. G. Cy" Key can be directly use to change to other colours screen.
21E1-RU
|
|
|
> |
|
