|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good product. Best service manual. Many thanks
;
I am only search for 5 Minute, by it in 5 Minutes to and get ist in few ours! Best i found in the Internet and my Amplifer is repaired as well! Thank you
 ;
Readable text and good copy. Very much needed if you wish to do some repairs on this fine old unit.
;
Fint forløb med levering af manualen. Kvaliteten af skanningen betegnes som middel
;
I found the manual to be clear concise and complete. It was of immense assistance when removing the unit as the unit was over 22 years old and the wiring diagram was unobtainable from the manufacturer. The exploded drawings were clear as were the instructions and labels.
EN 60
8.
L01.1A AC
Alignments
A2T (TV A2 Threshold) Default value is 250. To adjust A2T: 1. To enter SDAM, press the following key sequence on the remote control transmitter: 0 6 2 5 9 6 directly followed by the MENU button (do not allow the display to time out between entries while keying the sequence). 2. Use the MENU UP/DOWN keys to highlight the AUDIO sub menu. 3. Press the MENU LEFT/RIGHT keys to enter the AUDIO sub menu. 4. Use the MENU UP/DOWN keys to select A2T. 5. Use the MENU LEFT/RIGHT keys to adjust the value of A2T to 250. 6. Press the MENU button to return to the top level SDAM menu. 7. To ensure the A2T setting is saved: � Turn the television set 'off' by using the 'POWER' button on the remote control transmitter or the local keyboard. Disconnect the television set from AC power for at least ten seconds. Reconnect the television set to AC power. Turn the television set 'on' by using the 'POWER' button on the remote control transmitter or the local keyboard
Parameter
20RF, 21RF, 25RF, 27RF, 29RF, 25", 28", 29"SF, 32V, 33"
25V 9 27V/29" 9
VX Vertical Zoom H60 Horizontal (NTSC) Shift Offset
25 9
25 25 25 25 25 35V 9 28WS 9 9 32WS 9 9
V60 Vertical Shift Offset (NTSC) 8.3.5 Audio
-2
-2 -2 -2 -2 -2 -2 -2 32WSRF
28WSRF
� � �
S
AF-M
XX
A2T
XX
CL 26532046_008.eps 040402
Figure 8-8 Audio alignment menu No alignments are necessary for the AUDIO sub menu. Use the default values. AF-M (NICAM threshold) Default value is 300. To adjust AF-M: 1. To enter SDAM, press the following key sequence on the remote control transmitter: 0 6 2 5 9 6 directly followed by the MENU button (do not allow the display to time out between entries while keying the sequence). 2. Use the MENU UP/DOWN keys to highlight the AUDIO sub menu. 3. Press the MENU LEFT/RIGHT keys to enter the AUDIO sub menu. 4. Use the MENU UP/DOWN keys to select AF-M. 5. Use the MENU LEFT/RIGHT keys to adjust the value of AF-M to 300. 6. Press the MENU button to return to the top level SDAM menu. 7. To ensure the AF-M setting is saved: � Turn the television set 'off' by using the 'POWER' button on the remote control transmitter or the local keyboard. � Disconnect the television set from AC power for at least ten seconds. � Reconnect the television set to AC power. � Turn the television set 'on' by using the 'POWER' button on the remote control transmitter or the local keyboard.
|
|
|
> |
|
