|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
MAINTENANCE
High speed needle H
� The carburettor is equipped with an automatic speed governor, which prevents a too high peripheral speed on the cutting disc. At full throttle with a unloaded cutting disc distinctive variations in speed can be heard. This is usual and is only a sign that the speed governor is working. � The high speed needle H affects the power cutter�s output and should be set according to the recommended basic setting, H = 3/4 turn open.
Fuel filter
� The fuel filter sits inside the fuel tank. � The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by blockage of the fuel filter. � The filter cannot be cleaned but must be replaced with a new filter when it blocked. The filter should be changed at least once per year.
H
Air filter
The air filter should be cleaned regularly removing dust and dirt to avoid: � Carburettor malfunction � Starting problems � Reduced engine power 2 � Unnecessary wear to engine parts 1 � Abnormal fuel consumption
� If adjustment is necessary proceed as follows: Screw the H-needle inwards to the limit position where the engine starts to hesitate with acceleration. Use short, fast acceleration from idling. From this position the H-needle is opened 1/4 turn (90°), which gives the carburettor setting for max. engine output. � Check using a tachometer that the stated maximum speed 10,000 rpm is not exceeded. NOTE! A high speed needle set too lean (H-needle screwed in too far)) reduces the power cutter�s output and causes overheating resulting in engine damage. The high speed needle H should be set for the highest output and not the highest speed. NOTE! Too obtain the optimal setting a technician with access to a tachometer should be contacted. The recommended maximum speed should not be exceeded.
A
The air filter system consists of a pre-filter and a main filter: 1)The pre-filter is an oiled foam filter that is easily accessible under the filter cover (A). When used in dusty conditions, this filter should be checked/replaced after every second tank of fuel. The filter must be cleaned and oiled regularly to obtain a satisfactory filtering effect. There is a special HUSQVARNA oil produced for this purpose (reference number 503 47 73-01). The bottle contains sufficient oil (0.1 l) for oiling the filter three times. � Remove the filter. Wash the filter carefully in tepid, soapy water. After cleaning rinse the filter thoroughly in clean water. Squeeze out the filter and let the filter dry. NOTE! Compressed air at a high pressure can damage the foam. � Oil the filter carefully. It is extremely important that the entire filter is saturated in oil. 2) The main filter is a paper filter and is accessible from under cover B. This filter should be changed/cleaned when the engine�s output drops or after 1-2 weeks. The filter is cleaned by shaking or carefully using compressed air. Note the filter must not be washed!
Correctly adjusted carburettor
A correctly adjusted carburettor means that the machine accelerates without hesitation and that the engine gurgles a little at full throttle. In addition the cutting disc should not rotate when idling. An L-needle set too lean can give starting difficulties and inferior acceleration. An H-needle set too lean gives lower engine output = �less power�, inferior acceleration and/or engine damage. A too rich setting of either the L or H needles gives acceleration difficulties or a too low working speed.
B
A filter used for a long period of time can never be completely cleaned. Therefore all air filters must be replaced periodically with a new filter. A damaged air filter must always be replaced.
18 � English
|
|
|
> |
|
