PHILIPS 27HT7210D/27
Owner's Manual

TV SETUP MENU & SUB-MENUS (CONTINUED)
· MIN VOLUME (||||||||||||| 0 - 63) 63) Specify the lowest volume setting possible by using the remote control or the TV front panel (if it is not locked out). This setting cannot exceed the MAX VOLUME. · MAX VOLUME (||||||||||||| 0 - 63) 63) Specify the highest volume setting possible by using the remote control or the TV front panel (if it is not locked out). This setting cannot be less than the MIN VOLUME. · SWITCH ON VOLUME (STANDARD / ||||||||||||| 0 - 63) 63) Specify the volume setting that takes effect when the TV is powered on. If STANDARD, the volume at power-on will be the volume at which the TV was prior to last power-down. If specified as 0 - 63, that will always be the volume at power-on, until SWITCH ON VOLUME is changed. · SWITCH ON CHANNEL (STANDARD / TV 1 - 125 / AV2 / SIDE / S-VIDEO / CVI) ) Specify the channel which the TV will be tuned when it is powered on. If STANDARD, the channel at power-on will be the same as the channel when the TV was tuned at last power-down. If specified (eg. 2, AV2, CVI etc.), then that will be the channel at power on until SWITCH ON CHANNEL is changed. · POWER ON (STANDARD / FORCED / RESTORED) ) STANDARD : The TV will be in standby mode when AC mains power is first applied after being disconnected. FORCED : The TV will turn ON whenever AC mains power is applied. This feature allows the TV's power status to be controlled for example from an AC mains breaker. RESTORED : When AC mains power is first applied after being disconnected, the TV's power status will revert to that when the AC mains power was last removed. · CHANNEL DISPLAY (NONE / NUMBER / LABEL / ALL) ) Specifies which of the respective channel properties are displayed by the TV's OSD when a channel or input is first selected. If REMINDER (see REMINDER page 17) is OFF, these properties will be displayed for a few seconds, then disappear. If REMINDER is ON, the channel properties remain on-screen as long as the TV is on. · KEYBOARD LOCK (NO / YES) ) NO : The TV's front panel is enabled. YES : The TV's front panel is disabled. · ESP - ENERGY SAVING PROGRAMMABILITY (OFF / 1 HR / 2 HR / ... / 99 HR) ) This feature enables the TV to automatically power-down after a specified period of time. If during this period it does not receive any commands from the remote control or TV front panel, this energy-saving feature assumes the TV is inactive, and will automatically power-down. · AUDIO / VIDEO MUTE (OFF / BLACK / BLUE) ) Also known as "A/V muting". Suppresses audio and video when the TV tuner is not receiving sufficient RF signal. These options produce the following results. OFF : TV screen displays "snow", and the audio appears as white noise ("static"). BLACK : TV screen display is black, and the audio is muted. BLUE : TV screen display is blue, and the audio is muted. · AUDIO / VIDEO OUT MUTE (NO / YES) ) When set to YES, it turns off the audio and video MONITOR OUT signals (either demodulated RF input or loop-through video). Intended to prevent recording of pay-per-view content. · MONITOR OUT RF (NO / YES) ) This feature configures the audio and video monitor outputs (provided the AUDIO / VIDEO OUT MUTE is not set to YES). NO : The signals that are present at the monitor outputs are the same as those of the currently selected channels or video input. The monitor outputs "track" what is viewed and heard on the TV. YES : Regardless of the current selected TV source (eg. AV2, S-VIDEO, CVI) input, the signal present at the monitor outputs is always the tuner output (see NOTE below).

Note : When The MONITOR OUT RF is initially changed from its current setting, the monitor out signal depends upon the previous
MONITOR OUT setting until a different TV source is selected. From then on, the new MONITOR OUT setting will perform as described.

15