|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The Service Manual for Sansui AU-9500 was very helpfull, in complete and in good printable condition.
Thanks.
;
Dear Sir,
Document is original service document of sharp. I had a problem with the door contacts. Fuses where blown. With the manual in a few minuts is was clear what the problem was.
Manual was of great help.
With kind regards,
Martie Verhoeven
The Netherlands.
 ;
The scan is clear and well readable with very few weaker spots, usually on black background with white letters, but with enough zoom those spots can be read.
Printout is clear, the manual is complete and has all pages scanned.
I would give 5 stars, except that it is not in color, and the schematic and PCB pages are scanned on multiple pages. The document is locked (except printing) so the pages can not be extracted to compose them together for printing on the large plotter
It is worth the price tag.
;
let's say first that i do not need to have a credit for my opinion, i am a retired sparkie and i voluteerd to fix an electronic device for a local "Youthgroup",as no diagram was present i checked the "net" and gambled on this site and paying some fee via PayPall, i was gladly surprised that the manual arrived as was stated, GOOD SHOW, and best wishes, John
;
I had been looking for a Manual for my CS2150 for quite a while -- in fact I had just about given up. I saw this site and decided to download the Manual. When I Received it by Email I was really pleased with what I got, with the result that My Kenwood 'Scope is now 100% repaired and working well. As an AV Serviceman, you need a good 'scope, and thanks to this site, and the Service Manual, I have been able to repair it. The Manual was a copy of the Factory Original and the copy was very clear, especially in the area of the Circuit Schematics, where You really need to be sure of what You are looking at.
No 43
Name PHI-1 FILTER
Description The loopfilter connected to pin 43 is suitable for various signal conditions as strong/weak and VCR signal. This is achieved by switching of the loopfilter time constant by changing the PHI-1 output current. Via I2C bus FOA/B, different time constants can be chosen, including an automatic mode which gives optimal performance under varying conditions. To this pin are connected the IC-substrate and horizontal output. The EW drive is a current output. The output is single-ended and is fed directly to the EW-input terminal The vertical drive has a current output. The output is balanced which ensures a good common mode behavior with temperature and makes the output signal less sensitive for disturbances. The PLL frequency range is 32-60MHz with corresponding VCO frequency 64-120MHz. The IF input impedances is 2 in parallel with 3pF and matches the required load for commonly used SAW filters. A DC coupling is allowed, so no series capacitors between SAW filter and IF input are necessary. The input range for EHT tracking is 1.2 ~ 2.8V, for a compensation of +/- 5% on vertical and/or EW. The tracking on EW can be switched on/off by HCO. The overvoltage protection is activated when the voltage on pin 50 exceeds 3.9V typical. This pin requires a capacitor to ground of l00nF +/- 5%. The optimal sawtooth amplitude is 3.5V and is determined by the external capacitor and charge current. The sawtooth bottom-level is 2V. This pin requires a resistor to ground. The optimal reference current is 100 . which is determined by this resistor. The AGC capacitor value is 2.2 and has been defined for an optimal compromise between AGC speed and tilt for all AGC modes (negative/positive modulation). This output is used to control (reduce) the tuner gain for strong RF signals. The tuner AGC is an open collector output which is acting as a variable current source to ground. not used. This pin requires a capacitor of 10 connected to ground. The pin acts as a low pass filter needed for the DC feedback loop.
44 45 46 47 48 49
GROUND EAST-WEST DRIVE VERT DRIVE + VERT DRIVE IF INPUT
50
EHT/OVERVOLTAGE PROTECT INPUT
51
VERT SAWTOOTH CAPACITOR REFERENCE CURRENT INPUT AGC DECOUPLING CAPACITOR
52 53
54
TUNER AGC OUTPUT AUDIO DEEMPHASSIS DECOUPLING SOUND DEMODULATOR
55 56
20
|
|
|
> |
|
