|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
No 43
Name PHI-1 FILTER
Description The loopfilter connected to pin 43 is suitable for various signal conditions as strong/weak and VCR signal. This is achieved by switching of the loopfilter time constant by changing the PHI-1 output current. Via I2C bus FOA/B, different time constants can be chosen, including an automatic mode which gives optimal performance under varying conditions. To this pin are connected the IC-substrate and horizontal output. The EW drive is a current output. The output is single-ended and is fed directly to the EW-input terminal The vertical drive has a current output. The output is balanced which ensures a good common mode behavior with temperature and makes the output signal less sensitive for disturbances. The PLL frequency range is 32-60MHz with corresponding VCO frequency 64-120MHz. The IF input impedances is 2 in parallel with 3pF and matches the required load for commonly used SAW filters. A DC coupling is allowed, so no series capacitors between SAW filter and IF input are necessary. The input range for EHT tracking is 1.2 ~ 2.8V, for a compensation of +/- 5% on vertical and/or EW. The tracking on EW can be switched on/off by HCO. The overvoltage protection is activated when the voltage on pin 50 exceeds 3.9V typical. This pin requires a capacitor to ground of l00nF +/- 5%. The optimal sawtooth amplitude is 3.5V and is determined by the external capacitor and charge current. The sawtooth bottom-level is 2V. This pin requires a resistor to ground. The optimal reference current is 100 . which is determined by this resistor. The AGC capacitor value is 2.2 and has been defined for an optimal compromise between AGC speed and tilt for all AGC modes (negative/positive modulation). This output is used to control (reduce) the tuner gain for strong RF signals. The tuner AGC is an open collector output which is acting as a variable current source to ground. not used. This pin requires a capacitor of 10 connected to ground. The pin acts as a low pass filter needed for the DC feedback loop.
44 45 46 47 48 49
GROUND EAST-WEST DRIVE VERT DRIVE + VERT DRIVE IF INPUT
50
EHT/OVERVOLTAGE PROTECT INPUT
51
VERT SAWTOOTH CAPACITOR REFERENCE CURRENT INPUT AGC DECOUPLING CAPACITOR
52 53
54
TUNER AGC OUTPUT AUDIO DEEMPHASSIS DECOUPLING SOUND DEMODULATOR
55 56
20
|
|
|
> |
|
