|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I do not have very much to say.
The price is quite covenient, delivery was better as promised (about 12 ours, against the specified 24 hours if I remember well), and the quality of the PDF is more than acceptable.
The Service Manual of Sansui R30 itself is also satisfactory: good graphic for schematics and layouts, simple and well structured.
Giovanni Bianchi
;
Happy to find finally a schematic for this amplifier. The schematic is of good quality, the pcb layout is useless: all is black. Never the less, it is very easy to find the components on the board using the schematics.
;
Hard to find manual was ready the next day. Scans were very legible (including schematics). All the essential parts of the service manual were present (adjustment procedure, schematics, and parts list). It would have been nice if the rest of the manual was included (disassembly procedure, theory of operation, etc.).
 ;
The Service Manual for the Kenwood KR-V55R provided by owner-manuals.com was as described/advertised. The contents provided the necessary information to effect a diagnosis of the unit. The schematics above all else was instrumental in tracing the the signal flow from component to component.
;
This manual was the factory original. Excellent value and contained all the details I needed. Easy dowwnload provided the information when I needed it.
SX-68JF200
29A-SX1 29A-SX5 29A-SX8
SUB CONT SUB-BRIGHT ADJUSTMENT
NO. Adjustment part Adjusting procedure conditions Waveform and others 3 MAX BEEM 1 Receive E-5CH (Monoscope pattern) with
R1633 standard mode.
2 Make image normal with the remote con-
troller.
3 Connect the beam ammeter between TP1601
4 Adjust the beam current to 1.7mA ± 50µA with
and TP1602. Ammeter full scale 3mA range TP1602 is connected at side of the ammeter. TP1601 is connected at + side of the ammeter.
R1633 (sub-contrast VR). Note : Apply adjustment after aging with the beam current 1,500 ± 50µA or more for 30 minutes or more. (On the white or green monocolour screen)
4-1 SUB-CONTRAST Receive the window pattern with AV input. Note 1 : Use �Y� of Minolta colour
2
I C bus 2 Make image normal with the remote conanalyzer CA-100 in adjust-
(RF signal) troller. ment 4-1, 4-2, 5-1, 5-2.
3 Select the SUB-CONTRAST adjustment mode
with the remote controller, and adjust 50% white to 110 ± 3cd.
4-2 SUB-CONTRAST 1 Select the DVD mode. Note 2 : Window pattern of signal
I C bus adjust2 Receive of the DVD signal generagenerator is same ad JA-2 ment (DVD tor. (Component signal) 12CH. signal) (Window pattern) Note 3 : Use the signal generator
14
left) black of the window pattern to
CUTOFF POINT pattern.
3 Make image normal with the remote con"SX-1006" for SUB-CONT.,
troller. SUB-BRIGHT adjustment.
4 Select the SUB-CONTRAST adjustment mode
(DVD) with the remote controller, and adjust 50% white to 110 ± 3cd.
5-1 SUB-BRIGHT 1 Receive the window pattern with AV input. * When E-2CH (Crosshatch pattern) or
2
I C bus adjust2 Make image normal with the remote conequivalent signal is received.
ment (RF signal) troller.
3 Select sub-bright adjustment mode 1 Make image normal with the
controller, and adjust the right dark white remote controller. area of window pattern to 2.7cd ± 0.3cd. 2 Adjust 3rd (1 thru 5 from the
5-2 SUB-BRIGHT 1 Select the DVD mode. sink.
2
I C bus adjust2 Receive of the DVD signal genera-
ment (DVD tor. (Component signal) (Window pattern) signal) 3 Make image normal with the remote con-
troller.
4 Select the sub-bright adjustment mode (DVD),
and adjust right dark white area of the window pattern to 2.7cd ± 0.3cd of the window
14
|
|
|
> |
|
