|
Who's Online
There currently are 5848 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This service manual helped me to repair my PIONEER. Iam very satisfied, that I found it here.
Even the price of manual was not so high that person would not be able to spend a few money.
But that is very worth spent money. Thanks
;
Excellent quality service manual. Quick processing, fair prices. Love to do business again. Thank you!!!
;
Excellent service manual, the only known point of note is the alignment of improvability scanned pages within the pdf page. The resolution is good.
;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
Mechanical Instructions 4.3
4.3.1
LC4.6E AA
4.
EN 7
Assy/Panel Removal
Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover. 1. Remove the screws, which secure the rear cover. The screws are located at the top, bottom, left and right sides; next to the Side/IO connections and SCART connection. There are also three deeper located screws next to the stands. 2. Lift the rear cover from the cabinet. Make sure that wires and flat foils are not damaged during cover removal.
1. Remove the middle fixation screw (1) from the bottom side of the connector plate (as this holds the SSB bracket). Note: Sometimes it is easier to loosen the complete connector plate and remove it together with the SSB. 2. Remove all connector fixation screws (2) from the front side of the connector plate. 3. Remove the two female screw locks (3) of the VGA connector. 4. Release the plastic cable clips (4) on the shielding and disconnect all cables from the SSB. Note: Be careful with the fragile LVDS connector on the SSB. 5. Now, completely remove the SSB (together with all the shieldings) from the set. 6. Once the SSB is out, remove the fixation screws (5) from the shielding. 7. Remove the shielding, it hinges at the left side (acc. photo). 8. Remove the fixation screws that hold the panel, and take out the panel. Notes: � Pay special attention to the EMC foam on the SSB shielding. These must be replaced in their initial positions � during set re-assembly. Insulate the tuner pins, so they cannot touch the shielding (see also figure �SDM Service jumper� in Chapter 5).
4.3.2
Side I/O Panel 1. Disconnect the cable from the panel. 2. To replace the complete bracket, remove the two fixation screws on either side of the panel. 3. Release the two fixation clamps and lift the panel out of the bracket.
4.3.3
LED + Switch Panel 1. Remove the two fixation screws. 2. Disconnect the cable from the rear of the panel.
4.3.6
LCD Supply Panel 1. Disconnect all cables from the panel. 2. Remove the fixation screws from the panel.
4.3.4
Top Control Panel 1. Remove the two fixation screws. 2. Release the two fixation clamps and lift the panel out of the bracket.
4.3.7
LCD Stand-by/Audio Panel 1. Disconnect all cables from the panel. 2. Remove the fixation screws from the panel.
4.3.5
Small Signal Board (SSB) 4.3.8
LCD Panel
2
1
3
2 4 4 4 3
1
E_14710_002.eps 210404
2
4
Figure 4-4 SSB Connector plate
1
E_14710_061.eps 030804
Figure 4-6 LCD panel disassembly 1. Remove the T10 screws (1) from the mounting frame. 2. Remove all mounting LCD panel T20 screws (2). 3. Important: Unplug the LVDS connector (3) at the LCD panel. Be careful, as this is a very fragile connector! 4. Unplug the following connectors (4). � LCD back light (disconnect at the LCD side) � Loudspeaker (easiest to disconnect at the speaker and to release the cable holders a little. � Top Control cable (disconnect at SSB side). � Cable between LED/Switch panel and SSB. 5. Lift the metal frame (together with all PWBs) from the LCD panel. 6. After removal of the frame, you can lift the LCD display from the set.
5 4
E_14710_003.eps 210404
Figure 4-5 Cover shield of the SSB
|
|
|
> |
|