|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The PDF copy was immediately available on download after the payment. However, I noticed that the document was in German, and Ihad to contact a German translator to get it translated it to English. The quality of document is legible can be used for my purpose.
 ;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
ASSEMBLY
Fitting a trimmer guard and Superauto II 1� trimmer head
(323L, 323LD, 325Lx, 325LDx)
Fitting other guards and cutting attachments
(323L, 323LD, 325Lx, 325LDx)
K
�
Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the �tting on the shaft and secure with the bolt (L).
K J I
G F I
B C
A
�
Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the �tting on the shaft and secure it with the bolt (L). Fit the drive disc (B) on the output shaft. Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. Insert the locking pin (C) in the hole to lock the shaft. To �t the trimmer head, �rst separate the two halves (see diagram). Proceed as follows: Insert a �nger into the centre hole of the cover (I) while grasping the cover with your other �ngers. Using the index �nger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). Pull apart the trimmer head, grasping the cover �rmly. Place the cover (I) and the support �ange (F) on the output shaft. Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).
� � � �
Fit the drive disc (B) on the output shaft. Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. Insert the locking pin (C) in the hole to lock the shaft. Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.
H
� � � � �
H
� �
�
To dismantle, follow the instructions in the reverse order.
Fitting the trimmer guard and trimmer head
(323C)
Guard
� Fit the guard as shown in the diagram. Tighten securely.
�
Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.
Trimmer head
� � � To dismantle, follow the instructions in the reverse order. � Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. Hold the dust cup with a spanner to prevent the shaft from rotating. Screw the trimmer head onto the shaft.
English
� 11
|
|
|
> |
|
