|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
 ;
Bought T4850 High End Tuner a few years ago, but i didn't know where all the buttons were used for. So i purchased the owners manual. Perfect! Just what i needed.
SAFETY INSTRUCTIONS
� Regularly check that the muf�er is securely attached to the machine. � Tighten the nut using the socket spanner. 35-50 Nm (3.55 kpm).
CAUTION! The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times. WARNING! Never use a machine with faulty safety equipment. The machine�s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired.
�
If the muf�er on your machine is �tted with a spark arrestor mesh then it should be cleaned regularly. A blocked mesh causes the engine to overheat, which can lead to serious damage. Never use a muf�er with a defective spark arrestor mesh.
!
Cutting equipment
IMPORTANT!
Cutting equipment
This section describes how to choose and maintain your cutting equipment in order to: � � Obtain maximum cutting performance. Extend the life of cutting equipment.
This section describes how to choose and maintain your cutting equipment in order to: Reduce the risk of blade thrust. Obtain maximum cutting performance. Extend the life of cutting equipment. Only use cutting attachments with the guards we recommend! See the chapter on Technical data. Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.
General rules
1
Only use cutting attachments with the guards we recommend! See the chapter on Technical data.
Trimmer head
� Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on Technical data.
2
Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.
�
Locking nut
Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared. The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter. Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. To increase the life of the cord it can be soaked in water for a couple of days. This will make the line tougher so that it lasts longer. IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration.
�
When �tting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.)
�
� �
English
�7
|
|
|
> |
|
