|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
 ;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
1
Surround loudspeakers There are two surround loudspeakers supplied. One is the active loudspeaker, including the RF receiver, a power switch, the mains supply, a channel selector, a red and black connector clip, a left/right surround loudspeaker switch and a 3.5 mm stereo jack to make a wired connection with your TV in case there is interference or the wireless connection is not possible.The other loudspeaker is a passive one which has to be connected with the active loudspeaker with the supplied speaker cable.
� �
Set the slide channel switch 1 at the bottom of the active loudspeaker to channel 1. (In the factory channel 1 has been chosen as the default channel.) See also Sound Setup, p. 10. Connect the active to the passive loudspeaker with the supplied speaker cable 2. Push the connector clip down, insert one end of the colour coded wire into the opening of one connector clip and push it up again. Insert the other end of the same colour coded wire in the same colour connector clip of the other loudspeaker. Do the same with the other wire in the other connector clips. Do not insert the wires too far. The Surround sound loudspeakers should always be located behind or to either side of the listener. If preferred you can also hang the loudspeakers on the wall. The maximum distance between the TV and the surround speakers should not exceed 15 m. Note: people moving around close to the TV may interfere with the sound transmission. Set the slide switch 3 to the right if the active loudspeaker is positioned to the right side of the listener, to the left if it is positioned to the left side of the listener (seen from the point of view of watching the TV). Connect the active loudspeaker to the mains with the mains cable 4. Switch on the active loudspeaker with the POWER switch 5. The red indicator at the front of the active surround speaker shows that the speaker is in standby. During sound transmission the indicator turns to green and back to red after 10-15 min. after the TV has been switched off. To switch the active speaker off, use the POWER switch. Insert the mains plug of the TV in the wall socket having a mains voltage of 220V-240V. To prevent damaging the mains (AC) cord which could cause a fire or electric shock, do not place the TV on the cord. Switch the TV on : Press the power switch A on the front of your TV. A green indicator on the front of the TV lights up and the screen comes on. If the indicator is red, press the - P + keys on the remote control. The green lamp blinks every time you press a key on the remote control. When you switch on your set for the first time, the menu LANGUAGE automatically appears on the screen. The explanation appears in different languages one at a time. Choose your own language and press the OK key on the remote control.
5
�
� � �
(
§
4
Preparation
|
|
|
> |
|
