|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Super manual it contains all the things you need to service your Marantz 2100.
;
A very easy to understand and use manual. Well worth the money.
 ;
Very good information with clear drawings. Thanks!
;
The ease of this purchase was a good start. The content of this manual was exactly all I needed to retore my Tandberg 64.
All of the mechanical and electrical information is contained in the manual and the quality of the document makes reading the data easy.
The exerience with the resource has made this my prime source for technical data.
;
Owner-manuals.com is the best Possibility to give vantage HIGH CLASS Elektronic COMPONENTS
a new Life.Thanks alot for your perfekt Service.
AK41 CHASSIS MANUAL ADJUSTMENTS PROCEDURE
A) PRELIMINARY Before starting with the alignment procedure, make sure that all the potentiometers on the chassis and also screen and focus pots are in the medium position. B) SYSTEM VOLTAGE ADJUSTMENT Inputs - AC power (220V 50 Hz). - PAL B/G test pattern via RF (PAL I test pattern for PAL I TV�s, SECAM D/K pattern, SECAM L/L´/K´ TV�s). Outputs - Digital voltmeter to anode of D110. Display - System voltage Action - Apply power. Check that The stand-by led lights. - Select TV mode and tune to the applied test pattern via local test keyboard. Chassis should start normally. - Adjust all analogue controls (volume, bass, treble, brightness, contrast, colour) to minimum settings. - Adjust VR127 according to the following different types of CRT�s SYSTEM VOLTAGE 135V±0.5V 135V±0.5V 135V±0.5V 135V±0.5V TYPE OF CRT PHILIPS A66EAK552X54 PHILIPS A66EAK071X54 VIDEOCOLOR A66ECY13X12 PHILIPS W66ESF002X44
C) AFC ADJUSTMENT Inputs - AC power. - 38.9 MHz test pattern for PAL B/G, PAL-SECAM B/G or 39.5 MHz test pattern for PAL I model (90dBmV) to Z403 SAW filter input terminals 1 and 2. Outputs - Digital Voltmeter to AFC point (pin22 of IC401) Display - AFC Voltage. Action - Adjust VL401 for 2.5±0.1 Volts. TV should automatically tune to a station when search tuning is activated. D) FOCUS ADJUSTMENT Inputs - AC power - PAL B/G test pattern via RF input. Outputs - Picture tube drive. Display - Picture Action - Select TV mode and tune to the signal. - Adjust focus potentiometer (the upper pot on the rear side of the FBT transformer) for optimum focusing.drive. E) SCREEN ADJUSTMENT Inputs - AC power - PAL B/G Colour Bar test pattern via RF Outputs - 1/100 Oscilloscope probe to RGB cathodes on CRT baseboard. NOTE:Ground pin of probe will be connected to 1st pin (GND) of the CRT socket. Display - RGB ratio Action - Select PAL B/G Colour Bar pattern using the local test keyboard and the user remote control unit. - Adjust all control functions (brightness, colour and contrast) to minimum settings. - Measure the most sensitive cathode - Adjust the screen potentiometer (lower pot on the rear side of FBT transformer) until cathode voltage becomes 150V. F) IF ADJUSTMENT FOR L� MODE Inputs - AC power. - 38.9 MHz test pattern for PAL B/G, PAL-SECAM B/G or 39.5 MHz test pattern for PAL I model. (90dBmV) to Z403 SAW filter input terminals 1 and 2. Outputs - Digital Voltmeter to AFC point. (pin22 of IC401) - Digital Voltmeter to AFC_L point. (pin14 of IC401) Display - AFC Voltage. Action - Firstly adjust VL401 for 2.5 ± 0.1 Volts. TV should automatically tune to a station. when search tuning is activated. - Adjust VR401 for 2.5±0.1 Volts at the AFC_L point.
17
|
|
|
> |
|
