|
|
|
Who's Online
There currently are 5690 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
;
Nice pdf file of the manual sent promptly. Thanks.
5
Repair facilities
changed data are stored into the EEPROM after returning to the SAM main menu via the OK key. The initial default value for all setting is 37. The factory settings of the colour temperatures are: WARM; R = 45, G = 32, B = 26 NORMAL; R = 37, G = X, B = Y COOL; R = 37, G = 32, B = 31 Remark: In NORMAL position the values X (G) and Y (B) are adjusted for 8500K colour temperature. � � �
L7.2E
11
All software is suspended till the DST mode is left. The dealer mode status is left if the stand-by command is received
5.7
Hotel-mode
Entering the hotel-mode : � � Select channel 38 Push the menu button on the local keyboard (vol. + & vol. - ) and the OSD-button of the RC simultaneously for 3 seconds. The screen shows the "HOTEL MODE SUB MENU "ON". Via this menu the wanted blanked channels can be selected.
5.5.7
GEOMETRY
The geometry menu contains the following information:
Leaving the hotel mode : � � S Same as entering the hotel mode. The screen shows the "HOTEL MODE SUB MENU "OFF".
Remarks: � In the HOTEL mode the Installation menu cannot be entered. When entering the hotel mode the maximum volume will be the current value. The set will always switch to a selectable channel when set is switched on.
HSH VSL VAM SC VSH
25 32 23 13 27 Upon enter into the picture geometry menu, the first item will be highlighted. The value can be incremented or decremented by pressing the control right or left key. EXIT The rest of the parameters can be scrolled through by using the control up/down keys. All changed data will be stored into the EEPROM after returning to the service main menu via the OK key. Abbreviation explanation � � � � � HSH - Horizontal shift VSL - Vertical linearity VAM - Vertical amplitude SC - S-correction VSH - Vertical shift
� �
HOTEL MODE SUB MENU "ON"
38
HOTEL ON
> 38
HOTEL CHANNEL
HOTEL MODE SUB MENU " OFF "
5.6
Use of Dealer Service Tool (DST)
With the SDM, under mentioned extra service features can be executed � � � Direct entering SDM via the "DEFAULT" button on the DST. Direct entering SAM via the "ALIGN" button on the DST. In case of no (OSD) picture the error buffer can be read out using the "BLINKING LED" procedure (see also paragraph 6.7) by pressing the "DIAGNOSE" button on the DST. 38 HOTEL OFF
Remark: The Hotel mode can only be activated if the Hotel mode option status (HO=ON), see table 2.
Remark: � Entry of the SDM and SAM via the DST is possible in all states, except from stand-by.
|
|
|
> |
|
