|
|
|
Who's Online
There currently are 5831 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
 ;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
;
Fast service, document is OK. Thanks! Searched for it long time.
;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
6gb33005.fm5 Page 35 Tuesday, September 11, 2001 9:53 AM
AFTER-SALES SERVICE
Before calling After-Sales Service
1. See if you can solve the problem yourself with the help of the �Troubleshooting guide�. Switch off the hood for a few minutes and re-start it 2. to see if the problem has cleared itself. 3. If the malfunction persists, call After-Sales Service. Specify: � the nature of the problem, � the model, � your full address, � your telephone number and area code. � The service code (number below the word SERVICE on the rating plate inside the hood behind the grease filter).
INSTALLATION
When installing the hood, the minimum distances from the cooktop must be respected, and the numerical sequence and additional instructions must be followed exactly as indicated on the Installation sheet.
External Exhaust Mode (A - see also installation sheet)
Cooking fumes and vapours are conveyed outside through a duct connected to the hood by means of a collar. The outlet duct diameter must be the same as that of the collar. If a flue-damper is to be installed, check that it can open and close freely when installation of the exhaust duct is complete. The hood can be supplied with one (upper) or two (upper and rear) exhaust outlet holes.
The hood is usually set up for using the upper exhaust outlet.
1. The collar must be seated in the upper exhaust outlet. Use the rear exhaust outlet (where present). 1. Where fitted, remove the cover closing off the rear outlet and collar. 2. Some models are fitted with a plastic deflector that closes off the rear outlet. If fitted, remove it. 3. Fit the collar in the rear outlet. 4. Put the cover (if fitted) in the upper outlet.
Warning! If the hood has a carbon filter, this should be removed.
Check that the switch inside the hood (if fitted) is in position �A� Extractor; if not, set it to this position.
Air Circulation Mode (F - see also installation sheet)
The air is filtered by a carbon filter and recycled into the surrounding atmosphere. The filtered air is released towards the kitchen ceiling. Check that the switch inside the hood (if fitted) is in position �F� Filter; if not, set it to this position. If the plug is provided, close off the upper exhaust hole.
Warning! If the hood does not have a carbon filter, order one and fit it before use.
Electrical connection
Before connecting the hood, make sure the voltage indicated on the rating plate corresponds to the voltage in your home. The plate is located inside the hood behind the grille. For GB this appliance is supplied without a plug and is intended for direct connection to fixed wiring in accordance with national wiring regulations. An all-pole disconnection switch with a minimum contact separation of 3 mm must be included in the fixed wiring in an easily accessible position. The Manufacturer shall not be liable for any damage or problem arising from the failure to comply with the above-mentioned instructions.
35
|
|
|
> |
|
