|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
 ;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the TV/DVD/VCR into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the TV/DVD/VCR is in DVD mode with the tray open.) 2. To put the TV/DVD/VCR into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differs depending on the models. "*******" differs depending on the models.
F/W Version Up Mode VERSION : Completed SUM : 7ABC
Model No : ******* VERSION : *.** ************.ab7
(*2)
Fig. c Completed Program Mode Screen
F/W Version Up Mode
Model No : ******* VERSION : *.**
At this time, no button is available. 6. Remove the disc on the tray. 7. Press [SELECT] button on the remote control unit to go to TV mode, or press [POWER] button on the unit to turn the power off. 8. Press [SELECT] button on the remote control unit to put the TV/DVD/VCR into DVD mode again. 9. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. d appears on the screen.
"*******" differs depending on the models.
Please insert a DISC for F/W Version Up.
EXIT: SELECT
Fig. a Version Up Mode Screen
The TV/DVD/VCR can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The TV/DVD/VCR enters the F/W version up mode automatically. Fig. b appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : CLEAR
EXIT: SELECT
F/W Version Up Mode VERSION : Reading...
Model No : ******* VERSION : *.** ************.ab7
Fig. d
10. Press [CLEAR] button on the remote control unit. Fig. e appears on the screen.
"*******" differs depending on the models.
(*1)
MODEL : ******* Version : *.** Region : *
Fig. b Programming Mode Screen
EEPROM CLEAR : OK
The appearance shown in (*1) of Fig. b is described as follows: No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. e
Programming... Writing new version data
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11. To exit this mode, press [CH. o / p] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off.
5. After programming is finished, the tray opens automatically. Fig. c appears on the screen and the checksum will be shown in (*2) of Fig. c.
1-9-1
T1200FW
|
|
|
> |
|
