|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was very accurate for the part that I was changing, I was able to order the correct part and had no issues with the replacement procedure. However, I was expecting to have more detailed repairs for the lower drive unit.
 ;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the TV/DVD/VCR into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the TV/DVD/VCR is in DVD mode with the tray open.) 2. To put the TV/DVD/VCR into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differs depending on the models. "*******" differs depending on the models.
F/W Version Up Mode VERSION : Completed SUM : 7ABC
Model No : ******* VERSION : *.** ************.ab7
(*2)
Fig. c Completed Program Mode Screen
F/W Version Up Mode
Model No : ******* VERSION : *.**
At this time, no button is available. 6. Remove the disc on the tray. 7. Press [SELECT] button on the remote control unit to go to TV mode, or press [POWER] button on the unit to turn the power off. 8. Press [SELECT] button on the remote control unit to put the TV/DVD/VCR into DVD mode again. 9. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. d appears on the screen.
"*******" differs depending on the models.
Please insert a DISC for F/W Version Up.
EXIT: SELECT
Fig. a Version Up Mode Screen
The TV/DVD/VCR can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The TV/DVD/VCR enters the F/W version up mode automatically. Fig. b appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : CLEAR
EXIT: SELECT
F/W Version Up Mode VERSION : Reading...
Model No : ******* VERSION : *.** ************.ab7
Fig. d
10. Press [CLEAR] button on the remote control unit. Fig. e appears on the screen.
"*******" differs depending on the models.
(*1)
MODEL : ******* Version : *.** Region : *
Fig. b Programming Mode Screen
EEPROM CLEAR : OK
The appearance shown in (*1) of Fig. b is described as follows: No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. e
Programming... Writing new version data
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11. To exit this mode, press [CH. o / p] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off.
5. After programming is finished, the tray opens automatically. Fig. c appears on the screen and the checksum will be shown in (*2) of Fig. c.
1-9-1
T1200FW
|
|
|
> |
|
