|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
70GS-66E
4. Once this data has been set, press the standby button to store. 5. If another NVM value has to be changed, use the channel down button to select the page or position and repeat as necessary. Note: DO NOT change any NVM data, unless you have been advised to do so by a Sharp representative. If data is incorrectly changed, serious damage may occur to the receiver. Contrast Adjustments Three types of contrast levels can be varied as listed below: � TELETEXT MIX MODE CONTRAST � TELETEXT CONTRAST � OSD CONTRAST Use the volume up/down buttons to adjust to a suitable level, then press the standby button to store. DVCO Adjustment (PAL) Carry out the DVCO Adjustment (PAL) as shown below: 1. Receive a Phillips pattern signal. 2. While in the DVCO ADJUSTMENT (PAL) menu, press the standby button. 3. The adjustment will be carried out automatically and stored.
DVCO Adjustment (NTSC) No adjustment required. Auto Installation On/Off To return the receiver to the original Auto Installation mode, using the volume up or down button, set the Auto Installation On/Off to On. This setting is automatically stored and when the receiver is turned on the next time it will start up in Auto Installation mode. AGC Adjustment To correctly align the Automatic Gain Control, follow the procedure outlined below: 1. Tune the set into a pattern generator on CH10. 2. Adjust the signal strength of the pattern generator to 57dB/uV 3. Enter the service mode. 4. Enter the AGC Adjustment menu. 5. Press the standby button on the remote control. 6. The adjustment will be carried out and stored automatically. AFT Adjustment To correctly align the Automatic Fine Tune, follow the procedure outlined below: 1. Tune the set into a pattern generator on CH69. 2. Enter the service mode. 3. Enter the AFT Adjustment menu. 4. Press the standby button on the remote control. 5. The adjustment will be carried out and stored automatically. AFT Adjustment (L�) To correctly align the Automatic Fine Tune, follow the procedure outlined below: 1. Tune the set into a pattern generator on CH04. 2. Enter the service mode. 3. Enter the AFT Adjustment menu. 4. Press the standby button on the remote control. 5. The adjustment will be carried out and stored automatically.
9
|
|
|
> |
|
