|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
 ;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
F. ADJUSTMENT PROCEDURE
ITEM Program Menu.
�Test Meter ﹡Test Point ﹫Pattern �Digital Voltmeter ﹡D510 Negative ﹫Crosshatch Pattern (31.5KHz,640x480)
Operation
Adjusting Value 15.5V ±0.2V
B+ Adjust A
1. Make the adjustment to the value shown at right by turning the VR501 on the main PCB.
High Voltage �Digital Voltmeter 1. Turn the power switch of the monitor OFF. Adjust �High Voltage 2. Connect high voltage probe to Anode Cap and Probe GND. B ﹡Anode Cap-GND 3. Turn the power switch of the monitor ON. ﹫Crosshatch Pattern (15 minutes) (31.5KHz,640x480) 4. Make the adjustment to the value shown at right by turning the VR601 on the main PCB.
26.0KV (17�,19�) 25.0KV ±0.1KV (15�)
Preset Adjust
﹫Crosshatch (31.5KHz,640x480)
1. Turn the power switch of the monitor OFF. 2. Hold encorder key,then turn the power switch of the monitor ON.(one key type) Hold MENU key,then turn the power switch of the monitor ON.(four key type) 3. Turn encorder/MENU key,make sure into preset picture,if not ,please return 1-2. 4. Please following the procedure of selection and adjusting an item using the OSD system as below steps for main function adjusent.
C
Contrast : MAX. Brightness MAX. H-Size : 260mm(15�) 310mm(17�) 360mm(19�) V-Size : 190mm(15�) One key model : 230mm(17�) Step 1 : Press and relese the OSD control knob to 270mm(19�) activate the OSD menu. H-Posi. : Step 2 : Turn the knob to highlight the desired option Center of OSD icon. V-Posi : Step 3 : Press and release the knob again to access the option. The color of the inner area of the OSD will changed from blue to green. Step 4 : To make your adjustment,turn the knob clockwise to increase or countclockwise to decrease the setting. Step 5 : Press and release the knob again to store the change.the color of the inner area will go back to blue.You can select EXIT icon and press the knob the exit the OSD menu. Center
11
|
|
|
> |
|
