|
Who's Online
There currently are 5691 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
SERVICE
Technical data
Water pressure Inlet pressure Spray pump pressure Rotations Spray pump motor Drain pump motor Spray arm lower Spray arm upper
Whirlpool Europe Customer Service
ADG 6556 IXM 8542 556 10740
14.02.2002 / Page 3 Doc. No: 4812 718 17313
Electrical base data 0.3 - 10 0.3 bar bar Voltage Frequency Total power Fuse 220/ 230 50 2.0 - 2.2 10 V Hz kW A
2800 3000 30 - 40 30 - 40
RPM RPM RPM RPM
Spray pump motor alternating spray system Voltage Power consumption HI HA Capacitor Drain pump motor Voltage Power consumption Resistance 220/ 240 V 30 W 146 � 220/ 240 125 79 60 4 V W � � µF
Spray arms, turning rhythm at alternating spray system Turning starts every time with the upper spray arm Pre wash Lower arm ~3min, Upper arm ~1min Main wash Lower arm ~3min, Upper arm ~5min Intermediate rinse Lower arm ~2min, Upper arm ~2min Final rinse Lower arm ~2min, Upper arm ~2min Service Test program Lower arm ~30sec, Upper arm ~30sec Remark: When switching of the main switch or interrupt the mains during the Test Program runs, then the alternating of the spray arms change in the test program to the rhythm of main wash 5/3 min. Important: To leaf the Test program is possible by made a break by customer (pushing the start button for 1.5 sec.) After �nishing the test program (End LED shines and/or Start LED goes of) must the appliance be switched off. If this will not be done, then the next normal wash will be made with the frequency of the Service Test Program ~30/30sec. Flow rates/ Inlet volume Flow meter (at 0.3 bar = quantity 1.1 l/min) Spray pump Drain pump Pump height max. Inlet valve Spray arm lower Sprayarm upper Shower top 208 45 - 65 16 1.1 4 ~ 33 ~ 27 ~8 lmp/l l/min l/min m l/min l/min l/min l/min
Heating 1 Element system Voltage Power consumption Resistance Heating speed Temperature on surface Safety thermostat self reset (Temperature of water) Fuse Potentiometer Points of meassurement: 1(black) to 2 (middle) Position 0 Position 1 Position 2 Position 3 Position 4 Position 5 Position 6 Water valves Single electric inlet valve Voltage Frequency Resistance 220/ 240 V 50/ 60 Hz 3.76 k� 0.0 0.5 1.0 1.4 1.8 2.3 2.6 k� k� k� k� k� k� k� 220/ 230 1.87/ 2.04 24.5 ~ 2.0 ~ 115 V kW � �C/min �C
~ 85 206
�C �C
|
|
|
> |
|