|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
NOTES: s When the air conditioner is off, the Room indicator light is lit and the display shows the current room temperature.
s
Fan Speed
NOTE: The Fan Speed button will operate only when Cool, Fan Only or Power Saver mode has been selected. 1. Press FAN SPEED until you see the indicator light come on for the setting you desire. 2. Choose Turbo, High or Low.
If the room temperature is below 55ºF (13ºC), the display will show 55ºF (13ºC). If the room temperature is above 99ºF (37ºC), the display will show 99ºF (37ºC). When the Set indicator light is lit, the display shows the temperature control setting. See �Temperature� later in this section. When the Hour indicator light is lit, the display shows the time remaining on the Timer setting. See �Timer Delay� later in this section.
s
s
1. Remove clear protective film from control panel and front panel badge (on some models). 2. Press POWER to turn on air conditioner.
Filter Monitor
1. When Filter indicator light is lit or flashing, remove, clean and replace air filter. See �Cleaning the Air Filter.� 2. Press and hold FILTER for 3 seconds after cleaning and replacing the air filter. This resets the Filter Monitor.
NOTE: When air conditioner is turned on for the first time after it is plugged in, it will display the default settings: Cool mode, Turbo fan speed, 72°F (22°C) for 3 seconds. When it is turned on at all other times, it will display the previous settings for 3 seconds, and then display the room temperature. 3. Select mode. See �Mode� later in this section. 4. Select fan speed. See �Fan Speed� later in this section. 5. Set temperature. See �Temperature� later in this section. NOTE: After 360 hours of fan operating time, the Filter indicator light will turn on. It will remain on for 180 hours or until you press FILTER. After 180 hours, it will flash. It will continue flashing until you press FILTER.
Mode
1. Press MODE until you see the indicator light come on for the setting you desire. 2. Choose Auto, Cool, Fan Only or Power Saver. s Auto�Cools room while it automatically controls fan speed. You cannot change fan speed, but you can adjust temperature by pressing the plus or minus button.
s s
Temperature
Press the plus button to raise the temperature. Room indicator light will turn off, and Set indicator light will turn on. Display shows the Temperature control setting. Each time you press or hold the plus button, the temperature will increase 1º until it reaches 86°F (30°C). NOTE: After 3 seconds, Set indicator light will turn off, and Room indicator light will turn on. Display will show the current room temperature.
Cool�Cools room. You can adjust temperature by pressing the plus or minus button. You can select fan speed by pressing FAN SPEED. Fan Only�Only the fan runs. You can select the fan speed by pressing FAN SPEED, but you cannot adjust the Temperature control setting. Display shows the current room temperature. Power Saver�Fan runs only when cooling is needed. You can select the fan speed by pressing FAN SPEED. Because the fan does not circulate the room air continuously, less energy is used, but the room air is not circulated as often. Use Power Saver when you are asleep or away from home.
s
s
s
Press the minus button to lower the temperature. Room indicator light will turn off, and Set indicator light will turn on. Display shows the Temperature control setting. Each time you press or hold the minus button, the temperature will decrease 1º until it reaches 64°F (18°C). NOTE: After 3 seconds, Set indicator light will turn off, and Room indicator light will turn on. Display will show the current room temperature.
10
|
|
|
> |
|
