|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
;
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
 ;
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
;
I am happy to get a rare TECHNICS SH-9090 Owner's Manual by PDF in clear copy.
;
Hr, klasse , good manual, verry fast on my e-mail, very usefull manual. rgds; ahm zeegers
Installing the Cabinet in a Window
s s
Handle air conditioner with care. Be sure your air conditioner cabinet does not fall out of the opening during installation or removal. The place where the power cord exits the air conditioner should be no more than 4 ft (122 cm) from a grounded outlet. Do not block the louvers on the front panel. Do not block the louvers on the outside of the air conditioner.
8. Pull cabinet part way out of window. Attach right filler board to front of a side-mounting angle with two ¹�� in. hex-head screws.
s
s s
2 1
Filler board installation
1. Center empty cabinet in window. Maintain a firm hold on the air conditioner cabinet. Lower window sash to hold cabinet in place. 2. Measure the distance between the right side of the cabinet and the inside of the window channel. 3. Repeat for the left side. 4. Adjust the cabinet until the distance on each side is the same. Then add ¹�� in. (3.2 mm) for the final measurement to be used in the next step.
3
1. Right filler board 2. Side-mounting angle 3. ¹�� in. hex-head screw
Top View
9. Place cabinet back into the window with right filler board tight against window channel. Insert left filler board into window channel.
1 2 1 Top View 3 2
1
1. Window sash 2. Empty cabinet 3. Window channel
2
1. Right filler board 2. Window channel
5. Use final measurement to measure in from each edge of the filler board. Mark lines in such a way that the outside edges of the filler board will contain the screw holes. 6. Place cardboard or other protective material on a sturdy, flat surface. Position filler board on top of the protective material to keep from cutting into the surface below. 7. Place a ruler or straight edge along the lines drawn previously and use a utility knife to cut filler boards to size along the lines. Make cut so the outside edges of filler boards will have screw holes.
10. Push left filler board against side-mounting angle and attach with two ¹�� in. hex-head screws. From the outside, push filler boards as far forward in window channels as possible.
Foam block installation
1. Measure the distance between the channel edge and the filler board. 2. Cut foam blocks ¹�� in. (6.4 mm) wider and insert into channel behind filler boards. Top View
1
3
2 3 4
1
1. Filler board 2. Window channel 3. Foam block
2
1. Lines 2. Screw hole
3. Long edge 4. Short edge
7
|
|
|
> |
|
