|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
;
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
required to hook up the canopy. Small adjustments can be made using the hood adjustment screws (see Fitting the canopy). The hood should have a maximum excursion of 20 mm. � Splashback (optional) When a splashback is to be fitted, the distance between the hood and the cooking appliances will be determined by the height of the splashback B and whether or not there is a raised back on the worktop. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes, care must be taken to ensure that the splashback is fitted at the correct height before fixing the base units or at least the worktop covering them. As this is a complex operation, it should only be undertaken by the technician installing the kitchen units or by a competent person who knows the final dimensions of the units. If the splashback is to be fixed through the top fixing holes only, proceed as follows: a) Rest the splashback on the worktop and against the wall, as illustrated in fig.2 . b) Mark the centres of the two holes in the top surface. c) Drill the wall using an 8 mm drill bit, and fix the splashback using the rawl plugs and screws provided. d) If necessary, the installer should secure the splashback to the wall by tucking the bottom edge down behind the rear of the worktop.
S1 S1
Fig. 3
1 1 1
Fixing the canopy
Fig. 4
Before starting to fix the canopy it will be necessary to adjust the support brackets S1 by turning the adjustment screws in a clockwise direction until their reach their limit (Fig.3): a) Hook the canopy onto the two size 4.2 x 44.4 screws 1 fitted as described above (Fig.4 ). b) Level the hood by turning the adjustment screws and then locking them.
Electrical connection and working test
� Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. � Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. � The appliance must be earthed. � Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly.
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
GB
17
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
|
|
|
> |
|
