|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Jog/Shuttle
Jog mode
Check that the JOG lamp has lighted.
Shuttle mode
pressed-in position. The SHTL lamp lights, and the shuttle mode is established. O Immediately after the power is turned on, turn the search dial and leave it at the center position.
1 Press the search dial so that it remains pressed in. 1 Press the search dial so that it is released from the 2 Turn the search dial.
The dial�s click-stops are released, and the tape is played back at the speed (�1a to +1a) corresponding to the speed at which the dial is turned. The maximum speed can be switched using setup menu No. 323 (JOG FWD MAX) and No. 324 (JOG REV MAX) settings. However, noise will occur at all speeds other than �0.43a to +0.43a. When the dial is no longer turned, the still picture mode is established.
2 Press the SHTL/SLOW button and switch to SHTL
or SLOW.
3 Turn the search dial.
O When the SHTL lamp among the JOG, SHTL and SLOW lamps is lighted, the playback picture speed changes from 0 up to ±32a depending on the dial position. This speed can be switched to ±8.4a, ±16a or ±32a using setup menu No. 101 (SHTL MAX). The dial has a click-stop at the center position where the still picture mode is established. O When the SLOW lamp among the JOG, SHTL and SLOW lamps is lighted, the playback picture speed changes from �4.1 up to +4.1a depending on the dial position. The maximum speed can be switched using setup menu No. 320 (VAR FWD MAX) and No. 321 (VAR REV MAX) settings. However, noise will occur at all speeds other than �0.43a to +0.43a, +0.5a and +0.75a. The dial has a click-stop at the center position where the still picture mode is established.
3 To transfer the VTR from the jog mode to another
mode, press the button that corresponds to the mode concerned. <Note> The direct search mode in which the VTR is transferred to the shuttle mode or jog mode by turning the search dial is set at the factory. By selecting KEY as the setup menu No. 100 (SEARCH ENA) setting, the VTR can be set to the mode in which it will not be transferred to the search mode unless the search button is pressed.
4 To transfer the VTR from the shuttle mode to
another mode, press the STOP button or other button. <Notes> O It is possible to listen to playback audio in the �10 to +10 speed range from the audio monitor output. (PCM must be selected for the setup menu No. 721 (MONI CH SELECT) setting.) O The audio playback sound heard in the search mode contains noise.
18
|
|
|
> |
|
