|
|
|
Who's Online
There currently are 6033 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
 ;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
3gb53241a.fm5 Page 43 Thursday, December 19, 2002 3:09 PM
INSTALLATION
ADJUSTMENT TO DIFFERENT TYPES OF GAS
If a different type of gas to the type shown on the rating plate and on the orange sticker affixed to the top of the cooktop is used, the cooktop must be converted to work with the new gas type. Remove the orange sticker and affix it to the instructions booklet, which must be retained for the lifetime of the appliance. Use pressure regulators suitable for the gas pressures indicated in the separate Product Description Sheet. 1. The gas nozzles must be changed by After Sales Service or a qualified technician. Nozzles not supplied with the appliance must be ordered from After Sales Service. 2. Connect the cooktop to the gas shut-off valve by means of a pipe suitable for the type of gas used, in compliance with current local regulations. 3. Adjust the minimum setting of the taps. Note: when liquid petroleum gas is used (G30/G31), the minimum gas setting screws must be tightened as far as they will go.
Replacing the injectors (see table in the enclosed Product Description Sheet)
1. Remove grids (A). 2. Extract burners (B). 3. Using a socket spanner of the appropriate size, (C), unscrew the injector to be replaced. 4. Replace it with the injector suitable for the new type of gas. 5. Re-assemble the injector in (D). 6. For models equipped with a triple crown burner, proceed as shown in figure. � Remove the two screws (F) followed by the cap (G) then replace both injectors (D) as previously described. Replace the cap (G), ensuring the seal is properly positioned before attempting to use the cooktop. Before installing the cooktop, remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration
Adjusting minimum gas setting of taps
1. To ensure that the minimum setting is correctly adjusted, remove knob (E) and proceed as follows: � tighten (-) to reduce the height of the flame; � loosen (+) to increase the height of the flame; The adjustment must be performed with the tap in minimum gas setting position (small flame) . Upon completion of adjustment, reseal using sealing wax or an equivalent material. 2. The primary air of the burners does not need to be adjusted. 3. After the adjustment of the minimum gas setting, light up the burners and turn the knobs from max. position to min. position to check the stability of the flame. 43
Black Process Plate
|
|
|
> |
|
