|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
OK?..manual is complet and helpfull... for repairing such a old and rare boombox like JVC PCM it is necessary...
;
Super Anleitung. Ordentliche Auflösung. Das ganze noch in Deutsch wäre zu schön. Alle Datenblätter sind sauber Kopiert und alle Leitungswege sind sauber ausgeführt
;
Thanks God for the internet and thanks for the service like this - proffessional solution on time.
;
About the service it's very fast and reliable. About the manual the quality is high enough to read even the tiniest details on the wiring diagrams so you can't ask much more than that, let it alone for a manual of a product from 20 years ago. Thank you, very satisfied.
;
The downloaded quality was as good as the orignial
XG-V10WU
AN-SD1U/S422U
ADJUSTING THE PC INTERFACE (CPCi-0042CE01. PC I/F Unit)
1. Initializing the EEPROM
1) Press S2601 to call the process mode. 2) Execute the S1 command on the SSS menu. (The S1 command is used to get the PC boards initialized. Do not carry out the S2 command because otherwise all the other adjustment data than on the PC boards would be initialized.) 3) Make sure the program version VER.XXX on the SPECIAL menu is the latest one.
2. Adjusting the levels
2-1. Preparing the oscilloscope 1) Set the oscilloscope range to 1 Vdc/div. and 5 µs/div. 2-2. Connecting the PC interface 1) Connect the PC interface to the set and make sure the P404, P405 and P502 connectors are all tight in position. 2) Connect a cable between the ANALOG OUTPUT terminal (signal generator) and the DSUB connector (projector's INPUT1). 3) Set the projector's INPUT SELECT to the INPUT1 position. 4) Set the signal generator to the SXGA mode (1280 x 1024, 60 Hz, 32 tones). Adjust the output amplitude between the black and white levels to 700 mVp-p (terminated with a 75-ohm impedance). 5) Turn on the power. 2-3. Adjusting and checking the levels 1) Press S2601 and call the process mode. 2) Adjust the SH-PHASE setting on the OUPUT3 menu to 8. (Make sure the onscreen display characters appear crisp and clear.) (Adjusting the A/D menu settings) 3) G-BRIGHT adjustment: Feed the black signal and adjust the G-BRIGHT setting on the A/D menu until there are bit dropouts. 4) R-BRIGHT adjustment: Feed the black signal and adjust the R-BRIGHT setting on the A/D menu until there are bit dropouts. 5) B-BRIGHT adjustment: Feed the black signal and adjust the B-BRIGHT setting on the A/D menu until there are bit dropouts. 6) G-D adjustment: Feed the white signal and adjust the G-D setting on the A/D menu until there are bit dropouts. 7) R-D adjustment: Feed the white signal and adjust the R-D setting on the A/D menu until there are bit dropouts. 8) B-D adjustment: Feed the white signal and adjust the B-D setting on the A/D menu until there are bit dropouts. 2-4. Adjusting the DTV settings 1) Feed the 480P Y signal to the INPUT1 terminal. Keep out the R (Pr) and B (Pb) signals. 2) G-BRIGHT adjustment: Feed the black signal and adjust the G-BRIGHT setting on the DTV menu until there are bit dropouts. 3) CR-OFFSET adjustment: Adjust the CR-OFFSET setting to 16. 4) CB-OFFSET adjustment: Adjust the CB-OFFSET setting to 16. 5) Press S2601 to exit from the process mode.
37
|
|
|
> |
|
