|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
;
This was the Sony CCU-500A Service manual I was looking for.
The price was reasonable.
The permission to download was quck.
I will use Owner-Manual.com for all my manual needs.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
4. Remove the ADU unit harness cover and connect the connector.
Remove the fixing screw of the ADU unit, and remove the harness cover. Remove the connector of the connector storing section, and connect it to the ADU unit connector. Attach the pawl section of the removed harness cover to the ADU unit and fix with a fixing screw. At that time, treat the wires so that the connector is stored inside the harness cover. Be careful not to pinch the wire with the harness cover. Insert the paper exit unit into the copier.
Harness cover Fixing screw Connector storing section
Rear side
0~0.5mm
When the alignment guide is not shifted:
remove the paper from the ADU unit, press the CA key and cancel the set mode.
When the alignment guide is shifted:
1 Insert the paper exit unit. 2 Change the set value.
[EXECUTE] By this operation, the set value is changed and alignment is performed again.
Set value
<Example> Connect the power plug of the copier to the power outlet, turn on the power switch, and follow the following procedures.
�
Setting to 45
4 5
[EXECUTE]
5. Change the system configuration setting.
1 Perform the mode setting with the key operation of the copier.
P C
2 6 0 1
When the set value is changed by 1, the alignment guide width is changed by 0.5 � 0.6mm.
5 Reference for changing the set value
40 (Shipment set value) 60 The guide is narrowed The guide is extended
The current set value is displayed with the above key operation. 2 Change the set value to 2.
C 2 OK
With the above operation, the set value can be changed.
(The value of 61 or greater or 39 or smaller is invalid.)
3 Pull out the paper exit unit again. 4 Check that the clearance between the alignment guide and paper is 0 � 0.5mm. At that time, be sure to shift the paper to the rear side of the alignment guide for checking. Repeat procedures 1 through 4 repeatedly. After adjustment, remove the paper from the ADU unit, press the CA key and cancel the set mode.
The set value can be changed with the key operation.
6. Check and adjust the alignment guide.
1 Set the adjustment mode of the alignment guide with the key operation of the copier.
P C
5 2 0 1
7. Print off-center adjustment
With the above key operation, the set value is displayed. A sheet of paper is fed from the paper feed section, and transported to the top of the alignment plate of the ADU unit and stopped under the aligned state. 2 Pull out the paper exit unit. 3 Check that the clearance between the alignment guide and the paper is 0 � 0.5mm. At that time, be sure to shift the paper to the rear side of the alignment guide for checking. 1 Make a copy. If the center is shifted, set the adjustment mode of the print off-center with the key operations of the copier.
P C
5 0 1 0
With the above key operation, the current set value is displayed. 2 Select the item of ADU from the message menu with [ � ] key and [ � ] key. Adjustment value: 1.7mm
�3�
|
|
|
> |
|
