|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was having a hard time finding the problem with this Mackie 1604 unit. I didn't have a schematic. Went looking on the web and found your site and the price was more then reasonable. Ordered it and within the hour had the manual and within 15 minutes had the unit fixed. Best $4.99 I ever spent. Thank you.
Doug
;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
AV-14F3/AV-1435 AV-1435EE/AV-1435TEE AV-14FMT3/AV-1438 AV-14FMG3/AV- 14FMG 3B
Measuring instrument Signal gener ator Remote control unit
Item Ad justment of VER. LIN. & VER. SCURVE
Test point
Ad justment part 4. VER. L IN. 5. VER. SCURVE � When the vertical
Description linearity has been deteriorated
rem arkably, perform the following steps. 15. Input a cross -hatch signal. 16. Select 4. VER. LIN. with the MENU �/� key. 17. Set the initial s etting value of 4. VER LIN. with the MENU - / + key. 18. Select 5. VER. SCURVE with the MENU �/ � key. 19. Set the initial setting value of 5. VER. SCURVE with the MENU - / + key.
T OP
CEN TER
20. Adjust 4. VER. LIN. and 5. VER. SCURVE so that the spaces of each line as shown in Fig.3 on TOP, CENTER and BOTTOM become uniform.
BOTT OM
Fig.3
Make sure that the adjustment is properly done on the screen of 60Hz mode. [NOTE] " Adjust to make both 50Hz & 60Hz are the same v. size and fine straight line. " When adjust again, adjust 50Hz mode first.
" When adjust in 60Hz mode, only 60Hz mode is adjust.
VSM PRESET SETTING
Item Measuring instrument Remote control unit Test point Ad justment part Description
Setting of VSM PRESET
TINT COLOUR BRIGHT CONT . SHARP
1. Enter the SERVICE MENU. 2. Select 4. VSM PRESET from the SERVICE MENU. 3. Select BRIGHT with the PICTURE MODE key. 4. Adjust the MENU �/� and MENU - / + key to bring the s et values of TINT � SHARP to the values shown in the below table. 5. Respectively select the VSM PRESET mode for SOFT and STANDARD, and make s imilar adjustment as in 3 above.
�
BRIGHT TINT COLOUR BRIGHT CONT. SHARP / :SELECT DISP : EXIT ** ** ** ** **
VSM PRESET VSM Setting Item TINT COLOUR BRIGHT CONT SHARP BRIGHT +15 +15 +15 +30 +15 STANDARD SOFT
� � �
+15
� � �
+11 +12
- / + : OPERATE
�
28
No. 52026
|
|
|
> |
|
