|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I had been looking everywhere for a proper service manual for this VCR. Everywhere else that has this available for download has a very light version. This is the full service manual with all aspects that would interest anyone looking for the service manual for the AIWA HV-MX100 Worldwide VHS VCR. Great quality (as always). A winner hands down. Best Quality.
 ;
Top quality manual. Covers all aspects you'd expect in a top quality service manual for this Panasonic VHS VCR. The manual resolution is high. Another top quality manual from the only site worth downloading manuals from! If you're looking for a manual for the PV-9662 VHS VCR, this is the one you'll want to get!
 ;
complete part-lists and pcb layout, schematic diagram is good enlargable,
 ;
Excellent, fast delivery, excellent product. Good luck!
 ;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
AV-27D503
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVE THE REAR COVER
" Unplug the power plug. 1. Remove the 12 screws marked ! "as shown in Fig.2. 2. Remove the rear c over toward you. * When reinstalling the rear cover, c arefully push it inward after inserting the chassis into the rear c over groove.
REMOVING THE SPEAKER
" After removing the rear cover and chassis. 1. Remove the 4 screws marked *" *"(Fig.2.) 2. Follow the s ame steps when removing the other hand speaker.
CHECKING THE MAIN PW BOARD
1. To check the backs ide of the MAIN PW Board. (1) Pull out the chassis . (Refer to REMOVING THE CHASSIS). (2) Erect the chassis vertically so that you can easily check the backside of the MAIN PW Board. [CAUTION] � � When erecting the chassis, be careful so that there will be no contacting with other PWB. Before turning on power, make sure that the CRT earth wire and other connectors are properly connected.
REMOVING THE CHASSIS
" After removing the rear cover. the 2 claws marked # (Fig.1 and Fig.2) under the both sides of the chassis from the front cabinet. 2. Draw the chassis backward along the rail marked the arrow direc tion marked %(Fig.2.). 1. Slightly raise the both sides of the c hassis by hand and remov e
$ (Fig.1)
in
(If necess ary, take off the wire clamp, c onnector�s etc.) * When c onducting a chec k with power supplied, be sure to confirm that the CRT earth wire is c onnected to the CRT SOCKET PWB and the MAIN PWB.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new c able tie. FRONT CABINET CHASSIS MAIN PWB
REMOVING THE TERMINAL BOARD
" After removing the rear cover. 1. Remove the 4 screws marked"& (Fig.2) "' . 2. When you pull out the TERMINAL BOARD, it can be removed.
REMOVING THE FRONT CONTROL PW BOARD
" After removing the rear cover and chassis.
C
1. Remove the 2 screws marked ( (Fig.2). 2. Then remove the FRONT CONTROL PWB.
REMOVING THE FRONT AV IN PW BOARD
" After removing the rear cover and chassis. 1. Remove the 2 screws marked ) (Fig.2.). 2. Then remove the FRONT AV IN PW B.
B
Fig. 1
6
No. 51946
|
|
 |
> |
|