|
Who's Online
There currently are 5589 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
;
Très-très bon site, facile, très bon prix.
Au futur besoin, je n’hésiterais à faire appel à vous.
Merci
AV32H20EUS AV28H20EUS AV28H20EUB
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power c ord. 2. Remove the 12 (28� models), 13 (32� model) screws marked A as s hown in the Fig. 1. 3. Withdraw the rear cover toward you.
REMOVING THE POWER & DEF PWB
" After removing the rear cover. " After removing the rear CHASSIS. 1. Remove the 3 screws marked G. 2. Remove the POWER & DEF PWB.
REMOVING THE CHASSIS
" After removing the rear cover. 1. Slightly raise the both sides of the c hassis by hand and remove the two claws under the both sides of the chassis from the front cabinet. 2. Withdraw the chass is backward. (If necess ary, take off the wire clamp, connectors etc.)
CHECKING THE PW BOARD
To check the back side of the PW Board. 1) Pull out the chassis . (Refer to REMOVING THE CHASSIS). 2) Erect the c hassis vertically so that you c an easily check the back side of the PW Board. [CAUTION] " When erec ting the chassis, be careful s o that there will be no contacting with other PW Board. " Before turning on power, make sure that the wire connector is properly connec ted. " When conducting a check with power supplied, be sure to c onfirm that the CRT EARTH WIRE (BRAIDED ASS�Y) is connected to the CRT SOCKET PW board.
REMOVING THE SPEAKER
" After removing the rear cover. 1. Remove the 2 screws marked B, and remove the speaker holder as s hown in Fig. 1. NOTE : When removing the screws marked B of the speaker remove the lower side screw first, and then remove the upper one. 2. Remove the 2 screws C attac hing the speak er. 3. Follow the s ame steps when removing the other hand speaker.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new c able tie.
REMOVING THE AV TERMINAL BOARD
" After removing the rear cover. 1. Remove the 3 screws marked D as shown in the Fig. 1. 2. Remove the 2 claws mark ed E under the CHASSIS as shown in Fig. 2. 3. Remove the AV TERMINAL BOARD slightly in the direction of arrow F as shown in Fig. 2.
AV SW PWB
AV TERMINAL BOARD
E
E
Fig. 2
6
No.51945
|
|
|
> |
|