|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
;
Quick delivery, the document was usefull, although the copy was i little bit unclear in the details.
4.8
ADJUSTMENT PROCEDURE Measuring instrument
4.8.1 CHECK ITEM Item B1 POWER SUPPLY check Test point Adjustment part Description (1) Receive the black-and-white signal. (color off) (2) Connect the DC voltmeter to the TP-E and TP91(B1) of S1 connector. (3) Confirm that the voltage is DC134.5V±2V. � After reparing the high voltage hold down circuit. This circuit shall be checked to operate correctly. (1) Turn the power switch to on. (2) Refer to the figure, connect the resistor between S1 connector 1-pin and 3-pin. (3) Make sure that the screen picture disappeares. (4) Disconnect the power plug. (5) Remove the resistor. (6) Again connect the power plug. (7) Turn the power switch to on. (8) Make sure that the normal picture is displayed on the screen.
5 4 3 2 1 S1 CONNECTOR
HVT 4
DC voltmeter S1 Connector 1-pin : TP-E 5-pin : TP-91 [MAIN PWB] S1 connector 1-pin : TP-E 3-pin : X-RAY1 [MAIN PWB]
HIGH VOLTAGE Resistor HOLD DOWN (19.0k�, check 1/4W)
HEATER
B1
4.8.2 TUNER / IF CIRCUIT Item IF VCO Measuring instrument Remote control unit Test point Adjustment part [9.VCO] CW transf. (T111) [MAIN PWB]
AFC STATUS (Turn to green)
TOO HIGH SYNC: AFC FINE GOOD TOO LOW YES ON 0
Description � It must not adjust without inputting the RF signal. (1) Receive the broadcast. (2) Select 9.VCO from the SERVICE MODE. (3) Set the "AFC" to "OFF" and "FINE" to "0". (4) Confirm that the color change from "TOO HIGH" to "TOO LOW" by CW transf. on MAIN PWB, and check the "SYNC" is "YES". (5) Adjust CW transf. until "GOOD" letters turns green. And then confirm that the "SYNC" is "YES" again. Adjustment can be done in this statement. (6) It return the "AFC" to "ON". (7) Push the [EXIT] key to exit the 9.VCO.
4.8.3 FOCUS Item FOCUS Measuring instrument Signal generator Test point Adjustment part FOCUS VR [In HVT] Description (1) Receive the cross-hatch signal. (2) While watching at the screen, adjust the FOCUS VR to the vertical and horizontal lines will be thinnest and sharpest center horizontal line. (3) Make sure that the picture is in focus even when the screen gets darkened.
1-22 (No.YA057)
|
|
|
> |
|
