|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
4.6.5 VIDEO CIRCUIT The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values.The setting values which adjust the screen to the optimum condition can be different from the initial setting values. Setting item (Adjustment item) 2. V/C 1.RGB BLK 2.CUTOFF R 3.CUTOFF G 4.CUTOFF B 5.WDR R 6.WDR G 7.WDR B (Do not adjust) 8.BRIGHT 9.CONTRAST 10.COLOUR 11.HUE 12.SHARP (Do not adjust) TV EXT PAL --- (OFF) 100 132 124 165 135 150 -30 40 36 ---2 0 18 322 284 1096 1137 Initial setting value SECAM --- (OFF) 100 132 124 165 135 150 -30 40 31 ---2 0 --322 284 1096 1137 NTSC --- (OFF) 100 132 124 165 135 150 -30 40 25 : NTSC 3.58 0 : NTSC 4.43 2 : NTSC 3.58 0 : NTSC 4.43 -2 0 --328 290 1108 1150
13.SC ADJ. (Do not adjust) 14.SIDE .P.P (Do not adjust) 15.SIDE .P.W (Do not adjust) REGULAR 14:9 ZOOM REGULAR 14:9 ZOOM Measuring instrument Signal generator Remote control unit
Item WHITE BALANCE
Test point
Adjustment part [2. V/C] 2.CUTOFF R 3.CUTOFF G 4.CUTOFF B 5.WDR R 6.WDR G 7.WDR B (Do not adjust)
Description � Set the PICTURE MODE to STD. � Set the COLOUR TEMP to NORMAL. (1) Receive a black and white signal (colour off). (2) Select 2.V/C. (3) Each select 2.CUTOFF R, 3.CUTOFF G, 4.CUTOFF B and adjust the screen until the black portion in the screen becomes black. (4) Each select 5.WDR R, 6.WDR G and adjust the screen until the white portion in the screen becomes white. NOTE: Do not adjust 7. WDR B (5) Press the [MENU] key and memorize the set value. (6) Change the contrast and brightness from low-light to high-light and check that the tracking of the white balance is good.
SUB BRIGHT
Remote control unit
[2. V/C] 8. BRIGHT
Receive any broadcast. Select 2.V/C. Select 8.BRIGHT. Set the initial setting value. If the brightness is not the best with the initial setting value, make fine adjustment until you get the best brightness. (6) Press the [MENU] key and memorize the set value.
(1) (2) (3) (4) (5)
1-24 (No.52125)
|
|
|
> |
|
