|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a high quality manual with clear schematic and components layout diagrams ; with service procedure included.
 ;
This service manual for the Kenwood KT-990D was reproduced really well ,is very legible and manual is complete.Combined with the low price paid,in the future,I will be checking Owner-Manuals.com any time I need a manual.
;
When I purchased this manual I had my doubts regarding the quality as the price was so reasonable as compared to other outlets.
The manual itself is of high standard the print is very clear as are the diagrams. Obviously with the diagrams one has to zoom in otherwise it is to small to be able to read.
Overall I am very pleased with the company who delivered as they said and with the manual they supplied.
I occasionally require a manual and now having registered with this company I shall order from them in the future.
;
I was at first dubious about payiong for downloaded manuals but having done so, I was extremely impressed with quality of the two manual I ordered, well worth the small price I paid.
I would highly recommend these to my friends.
;
reasonable price for the schematic - the service is perfect, all as expected and pointed by instructions - good scan of the original plans - thank you!
AV-27D201 AV-32D201
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVE THE REAR COVER
" Unplug the power cord plug. 1. Remove the 12 screws marked A as shown in Fig.2. 2. Remove the rear cover toward you. When reinstalling the rear cover, carefully push it inward after inserting the chassis into the rear cover groove.
REMOVING THE SPEAKER
" After removing the rear cover and chassis. 1. As shown in Fig.2, remove the 4 screws marked H . 2. Follow the same steps when removing the other hand speaker.
CHECKING THE MAIN PW BOARD
1. To check the backside of the MAIN PW Board. (1) Pull out the chassis. (Refer to REMOVING THE CHASSIS). (2) Erect the chassis vertically so that you can easily check the backside of the MAIN PW Board. [CAUTION] � � When erecting the chassis, be careful so that there will be no contacting with other PWB. Before turning on power, make sure that the CRT earth wire and other connectors are properly connected.
REMOVING THE CHASSIS
" After removing the rear cover. 1. Slightly raise the both sides of the chassis by hand and remove the
2
claws under the both sides of the chassis from the front
cabinet. 2. As shown in the Fig.2, withdraw the chassis backward along the rail in the arrow direction marked B . (If necessary, take off the wire clamp, connector�s etc.) When conducting a check with power supplied, be sure to confirm that the CRT earth wire is connected to the CRT SOCKET PWB and the MAIN PWB.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
REMOVING THE TERMINAL BOARD
" After removing the rear cover. 1. As shown in Fig.2, remove the 4 screws marked C . 2. As shown in Fig.1, after removing the claw marked
D
in the
TERMINAL BOARD
direction of arrow mark. 3. When you pull out the TERMINAL BOARD in the direction of arrow marked E as shown in Fig.1, it can be removed. 4. Thus the connector should be securely inserted when the TERMINAL BOARD is installed again.
E
REMOVING THE FRONT CONTROL PW BOARD
" After removing the rear cover and chassis. 1. As shown in Fig.2, remove the 3 screws marked F . 2. Then remove the FRONT CONTROL PWB.
REMOVING THE FRONT AV IN PW BOARD
" After removing the rear cover and chassis.
D Fig. 1
1. As shown in Fig.2, remove the 2 screws marked G . 2. Then remove the FRONT AV IN PWB.
6
No. 51686
|
|
|
> |
|
