|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
got exactly what i ordered in a very timely manner. will use again for other manuals
 ;
I'm happy. Good quality. Very helped me with my work..............................
;
This is the second Manual I have ordered from owner-manuals, I give it five stars because it is exactly what I expected given the age of the equipment. So the contents look a bit aged and the pictures a bit grainy, it fulfills my needs and I am glad I can still get hold of them.
;
thank u so much for this manual that was so cheap that i thought it was a scam but i gambled anyway because it was too good of a deal to pass up and behold,the manual has everything and details of everything even the screws and im still amazed and very happy with my manual .so take my word and jump on it before they realize how cheap they selling thier manuals..thank you so much for taking time to read my thoughts
;
I do not have very much to say.
The price is quite covenient, delivery was better as promised (about 12 ours, against the specified 24 hours if I remember well), and the quality of the PDF is more than acceptable.
The Service Manual of Sansui R30 itself is also satisfactory: good graphic for schematics and layouts, simple and well structured.
Giovanni Bianchi
AV-36F703 AV-36F713 AV-36F803
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Disc onnect the power plug from AC outlet. 2. As s hown in the Fig.1, remove the 12 screws marked !. 3. Withdraw the rear c over backward.
CHECKING THE CHASSIS
To check the PW Board from back side. 1. Pull out the chassis (refer to REMOVING THE CHASSIS). 2. Erect the chas sis vertically so that you c an easily check the back side of the PW Board.
REMOVING THE TERMINAL BOARD
" After removing the rear c over. 1. As s hown in Fig.1, remove the screws marked 2. Withdraw the terminal board toward you.
[CAUTION]
".
" When erecting the chassis, be careful so that there will be no contacting with other PW Board. " Before turning on power, make s ure that the wire connec tor is properly connec ted. " When conducting a check with power supplied, be sure to confirm that the CRT EARTH WIRE (BRAIDED ASS�Y) is connected to the CRT SOCKET PW boar d.
REMOVING THE CHASSIS
" After removing the rear c over and terminal board. 1. Slightly raise the both sides of chassis by hand and remove the
2 claws under the both side of the chassis from the front cabinet.
2. Withdraw the chass is backward. (If necess ary, remove the wire clamp, c onnectors etc.)
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the c able tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
REMOVING THE SPEAKER
" After removing the rear cover. 1. As shown in Fig. 1, removing the 2. Then remove the 2 screws marked from speaker holder. NOTE : When removing the
2
screws marked
#,
then
remove the speaker with the speaker holder
$%to $%
detac h the s peaker
3. Follow the s ame steps when removing the other hand speak er.
2
screws mark ed
#
of the speaker,
remove the lower side screw first, and then remove the upper one.
REMOVING THE LED & POWER SW PWB
" After removing the rear c over and terminal board. 1. Remove the 2 screws marked & as s hown in Fig.1. 2. Withdraw the LED & POWER SW PWB toward you. * If nec essary, remove the wire c lamp, connector etc.
REMOVING THE FRONT CONTROL PWB
" After removing the rear c over & terminal board. 1. Remove the 2 screws marked ' as s hown in Fig.1. 2. Withdraw the FRONT CONTROL PWB toward you. * If nec essary, remove the wire c lamp, connector etc.
8
No.52003
|
|
|
> |
|
