|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a fantastic site, ad I have been a returning satisfied cusumer!
Thanx for a great sevice!
;
Je suis audiophile belge, électronicien et créateur d'enceintes acoustiques.
J'ai apprécié la qualité des documents fournis. Ils sont très lisibles, ils peuvent être agrandis sans problème et ils sont complets. Pour moi, c'est parfait. Pour cette qualité, je suis d'accord de payer. Et le système de paiement et d'envoi est simple. Merci, continuez comme cela.
Frédéric
;
The cover page was a little scary, very dark but readable. The remainder of the document was better copy and easily readable. Why would I give 5 Stars? (1) PRICE, (2) AUTHENTICITY, It was the real deal, filled with service information, including the specific information I required. (3) PRIVACY, I didn't start to get slammed with spam. (4) EASY TRANSACTION. Painless. (5) COMPLETE, I have found several manuals here, that I could find nowhere else. (6) I will be a repeat customer!
;
Well done!!! I found what I need to have, indeed!
Furthermore, due to my hobby is repairing vintage equipments, I added this web site in my desk toolbar because I have in mind to search further service manuals. Thanks a lot www.owner-manuals.com !
Regards, Maurizio
;
Again very good service manual, this time very fast download. AAAAA+
AV-N29301 AV-N34301
SPECIFIC SERVICE INSTRUCTION
DISASSEMBLY PROCEDURE
REMOVE THE REAR COVER
" Unplug the power plug. 1. Remove the 12 screws marked A as shown in Fig.2. 2. Remove the rear cover toward you. * When reinstalling the rear cover, carefully push it inward after inserting the chassis into the rear cover groove.
REMOVING THE SPEAKER
" After removing the rear cover and chassis. 1. As shown in Fig.2, remove the 4 screws marked H . 2. Follow the same steps when removing the other hand speaker.
CHECKING THE MAIN PW BOARD
1. To check the backside of the MAIN PW Board. (1) Pull out the chassis. (Refer to REMOVING THE CHASSIS). (2) Erect the chassis vertically so that you can easily check the backside of the MAIN PW Board.
REMOVING THE CHASSIS
" After removing the rear cover. 1. Slightly raise the both sides of the chassis by hand and remove the
2
claws under the both sides of the chassis from the front
cabinet. 2. As shown in the Fig.2, withdraw the chassis backward along the rail in the arrow direction marked B . (If necessary, take off the wire clamp, connector�s etc.) * When conducting a check with power supplied, be sure to confirm that the CRT earth wire is connected to the CRT SOCKET PWB and the MAIN PWB.
[CAUTION] � When erecting the chassis, be careful so that there will be no contacting with other PWB. � Before turning on power, make sure that the CRT earth wire and other connectors are properly connected.
WIRE CLAMPING AND CABLE TYING
1. Be sure to clamp the wire. 2. Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
REMOVING THE TERMINAL BOARD
" After removing the rear cover. 1. As shown in Fig.2, remove the 3 screws marked C . 2. As shown in Fig.1, after removing the claw marked D in the direction of arrow mark. 3. When you pull out the TERMINAL BOARD in the direction of arrow marked E as shown in Fig.1, it can be removed.
TERMINAL BOARD
E REMOVING THE FRONT CONTROL PW BOARD
" After removing the rear cover and chassis. PIP PWB 1. As shown in Fig.2, remove the 3 screws marked F . 2. Then remove the FRONT CONTROL PWB.
REMOVING THE FRONT AV IN PW BOARD
" After removing the rear cover and chassis. 1. As shown in Fig.2, remove the 2 screws marked G . 2. Then remove the FRONT AV IN PWB.
D
Fig. 1
6
No. 51738
|
|
|
> |
|
