|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
 ;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
;
Great copy of the manual, has all information required for servicing,
;
I work at an authorized service center and I can tell if a manual is as it should be. This one is. It may be a scan, but a very good one at that. The interesting part for me was the curcuit diagram which was scanned at high quality, making it as good as the original. I will definitely be back as a customer. I need not say this, but I will: the price was the best. Thank you owner-manuals.com .
;
really a very good manual even sometimes the quality is no so good as before still very readible and very very useful!
AV-N29304 AV-N29430 2.5 DISASSEMBLY PROCEDURE 2.5.1 (1) (2) (3) (4) 2.5.2 (1) (2) (3) (4) REMOVING THE REAR COVER [AV-N29304] Unplug the power plug. Remove the 11 screws [A] (Fig.1). Remove the 4 screws [B] (Fig.1). Then remove the REAR COVER toward you. REMOVING THE REAR COVER [AV-N29430] Unplug the power plug. Remove the 7 screws [A] (Fig.2). Remove the 4 screws [B] (Fig.2). Then remove the REAR COVER toward you. 2.5.6 CHECKING THE PW BOARD (1) Pull out the MAIN PWB (refer to REMOVING THE MAIN PWB). (2) Erect the MAIN PWB vertically so that you can easily check the backside of the PW Board. CAUTION: � When erecting the chassis, be careful so that there will be no contacting with other PW Board. � Before turning on power, make sure that the wire connector is properly connected. � When conducting a check with power supplied, be sure to confirm that the CRT EARTH WIRE (BRAIDED ASS'Y) is connected to the CRT SOCKET PW board. 2.5.7 WIRE CLAMPING AND CABLE TYING (1) Be sure to clamp the wire. (2) Never remove the cable tie used for tying the wires together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
2.5.3 REMOVING THE MAIN PWB � Remove the REAR COVER. (1) Raise this side of the MAIN PWB, and remove the PWB STOPPER [C] from the cabinet. (2) Withdraw the MAIN PWB backward. (If necessary, remove the wire clamp, connectors etc.)
2.5.4 REMOVING THE SPEAKER [AV-N29304] � Remove the REAR COVER. (1) Remove the 4 screws [D], then remove the speaker (Fig.1). (2) Follow the same steps when remove the other hand speaker.
2.5.5 REMOVING THE SPEAKER [AV-N29430] � Remove the REAR COVER. (1) Remove the 4 screws [D], then remove the speaker (Fig.2). (2) Follow the same steps when remove the other hand speaker. NOTE: When removing the 4 screws [D] of the speaker, remove the lower side screw first, and then remove the upper one.
1-6 (No.52129)
|
|
|
> |
|
